Makita RT001GZ18 Page 9 Instruction Manual Download

Page: 9 / 35

9 ENGLISH

NOTICE:

If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE:

The speed adjusting dial can be turned

only as far as 5 and back to 1. Do not force it past

5 or 1, or the speed adjusting function may no

longer work.

Electronic function

The tool is equipped with the electronic functions for

easy operation.
•

Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

•

Soft start

The soft-start function minimizes start-up shock,

and makes the tool start smoothly.

•

Soft brake

The tool stops gently with the soft brake. The soft

brake prevents damage to the workpiece due

to recoil and allows you to start next operation

earlier.

If the tool consistently fails to stop the trimmer bit

after the switch is turned off, have the tool ser

viced at a Makita service center.

ASSEMBLY

CAUTION:

Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing trimmer bit

NOTICE:

Do not tighten the collet nut without

installing a trimmer bit, or the collet cone may

break.

Insert the trimmer bit all the way into the collet cone.

Press the shaft lock and tighten the collet nut with the

wrench.

Fig.6

►

Shaft lock

Loosen

Tighten

Wrench

Collet nut

You can also tighten the collet nut securely with the two wrenches.

Fig.7

►

Wrench

Loosen

Tighten

Collet nut

To remove the trimmer bit, follow the installation procedure in reverse.

NOTE:

The shaft lock may not return to the original position when

you tighten the collet nut in the installation of the trimmer bit. The

shaft lock returns to the original position when you start the tool.

Fig.8

►

Shaft lock

Changing the collet cone

CAUTION:

Use the correct size collet cone for

the trimmer bit which you intended to use.

CAUTION:

Do not tighten the collet nut without

installing a trimmer bit, or the collet cone may break.

Loosen the collet nut and remove.

Replace the installed collet cone with desired collet cone.

Reinstall collet nut.

Fig.9

►

Collet cone

Collet nut

Summary of Contents for RT001GZ18




































Search results

Summary of Contents for RT001GZ18

Reviews:

Related manuals for RT001GZ18

Brands by name

Popular brands

Makita RT001GZ18, Instruction Manual

Search results

Summary of Contents for RT001GZ18

Reviews:

Related manuals for RT001GZ18

Brands by name

Popular brands