Makita RT001GZ18 Instruction Manual Download

Page: 8 / 35

8 ENGLISH

Overheat protection

When the tool or battery is overheated, the tool stops

automatically. In this case, let the tool and battery cool

before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Protections against other causes

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically. Take all the following steps to clear the

causes, when the tool has been brought to a temporary

halt or stop in operation.

1. Turn the tool off, and then turn it on again to

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

To turn on the tool, press the lock/unlock button. The

tool turns into the standby mode. To start the tool, press

the start/stop button in the standby mode. To stop the

tool, press the start/stop button again. The tool turns

into the standby mode. To turn off the tool, press the

lock/unlock button in the standby mode.

Fig.3

►

Lock/unlock button

Start/stop button

NOTE:

If the tool is left for 10 seconds without any

operation in the standby mode, the tool automatically

turns off and the lamp goes off.

NOTE:

You can also stop and turn off the tool by

pressing the lock/unlock button while the tool is

operating.

Lighting up the front lamp

CAUTION:

Do not look in the light or see the

source of light directly.

To turn on the lamp, press the lock/unlock button. To

turn off the lamp, press the lock/unlock button again.

NOTICE:

When the tool is overheated, the lamp

blinks. Cool down the tool fully before operating

the tool again.

NOTE:

Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Fig.4

►

Lamp

Speed adjusting dial

The rotation speed of the tool can be changed by turning

the speed adjusting dial. The table below shows the num

ber on the dial and the corresponding rotation speed.

Fig.5

►

Speed adjusting dial

Number

Speed

10,000 min

-1

15,000 min

-1

21,000 min

-1

26,000 min

-1

31,000 min

-1

CAUTION:

Do not change the rotation speed

during operation.

Otherwise unexpected reaction of

the tool may cause an injury.

Summary of Contents for RT001GZ18




































Search results

Summary of Contents for RT001GZ18

Reviews:

Related manuals for RT001GZ18

Brands by name

Popular brands

Makita RT001GZ18, Instruction Manual

Search results

Summary of Contents for RT001GZ18

Reviews:

Related manuals for RT001GZ18

Brands by name

Popular brands