6 English
• If electrolyte gets into your eyes, rinse them out with
clear water and seek medical attention right away. It
may result in loss of your eyesight.
• Do not short the battery cartridge.
• Do not store and use the tool and battery cartridge in
locations where the temperature may reach or exceed
50 °C (122 °F).
• Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the battery
cartridge. Such conduct may result in a fire, excessive
heat, or explosion.
• Do not use a damaged battery.
• The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on packaging
and labeling must be observed. For preparation of
the item being shipped, consulting an expert for
hazardous material is required. Please also observe
possibly more detailed national regulations. Tape
or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging.
• Use the batteries only with the products specified
by Makita. Installing the batteries to non-compliant
products may result in a fire, excessive heat,
explosion, or leak of electrolyte.
• If the tool is not used for a long period of time, the
battery must be removed from the tool.
• During and after use, the battery cartridge may take on
heat which can cause burns or low temperature burns.
Pay attention to the handling of hot battery cartridges.
• Do not touch the terminal of the tool immediately after
use as it may get hot enough to cause burns.
• Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery cartridge.
It may result in poor performance or breakdown of the
tool or battery cartridge.
• Unless the tool supports the use near high-voltage
electrical power lines, do not use the battery cartridge
near high-voltage electrical power lines. It may result
in a malfunction or breakdown of the tool or battery
cartridge.
• Keep the battery away from children.
11. Tips for maintaining maximum battery life.
• Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
• Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
• Charge the battery cartridge with room temperature
at 10 °C - 40 °C (50 °F - 104 °F). Let a hot battery
cartridge cool down before charging it.
• When not using the battery cartridge, remove it from
the tool or the charger.
• Charge the battery cartridge if you do not use it for a
long period (more than six months).
CAUTION:
Only use genuine Makita batteries. Use
of non-genuine Makita batteries, or batteries that have
been altered, may result in the battery bursting causing
fires personal injury and damage. It will also void the
Makita warranty for the Makita tool and charger.
Save all warnings and
instructions for future reference.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the appliance is switched off, and
the battery cartridge is removed before adjusting or
checking function on the appliance.
Installing or removing battery cartridge
CAUTION:
• Hold the appliance and the battery cartridge firmly
when installing or removing battery cartridge.
Failure to hold the appliance and the battery cartridge
firmly may cause them to slip off your hands and result
in damage to the appliance and battery cartridge and
a personal injury.
• Be careful not to trap finger(s) between the appliance
and battery cartridge when loading battery cartridge as
well as between the appliance and the battery cover
when closing the battery cover.
To install the battery cartridge, release the cover lock,
and open the battery cover.
(Fig. 1)
Insert the battery cartridge. Align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Then close the battery cover.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
(Fig. 2)
CAUTION:
• Always install the battery cartridge fully in place. If not,
it may accidentally fall out of the appliance, causing
injury to you or someone around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
Summary of Contents for ML005G
