Makita LS1040N, Instruction Manual

Page: 12 / 44

12
Safety cover (Fig. 10)
When lowering the handle, the safety cover rises auto-
matically. The cover returns to its original position when
the cut is completed and the handle is raised. NEVER
DEFEAT OR REMOVE THE SAFETY COVER. In the
interest of your personal safety, always maintain the
safety cover in good condition. Any irregular operation of
the safety cover should be corrected immediately.
NEVER USE THE TOOL WITH A FAULTY SAFETY
COVER. If the see-through safety cover becomes dirty, or
sawdust adheres to it in such a way that the blade and/or
workpiece is no longer easily visible, unplug the saw and
clean the cover carefully with a damp cloth. Do not use
solvents or any petroleum-based cleaners on the plastic
cover.
Dust bag (Fig. 11 & 12)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit the
bag’s entry port over the dust spout. When the dust bag
is about half full, remove the dust bag from the tool and
pull the fastener out. Empty the dust bag of its contents,
tapping it lightly so as to remove particles adhering to the
insides which might hamper further collection.
Switch action
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
• When not using the tool, remove the lock-off button and
store it in a secure place. This prevents unauthorized
operation.
• Do not pull the trigger hard without pressing in the lock-
off button. This can cause breakage of the switch.
For all countries other than European countries
(Fig. 13)
To prevent the trigger from being accidentally pulled, a
lock-off button is provided. To start the tool, press in the
lock-off button and pull the trigger. Release the trigger to
stop.
For European countries (Fig. 14)
To prevent the trigger from being accidentally pulled, a
lock-off button is provided. To start the tool, push the
lever to the left, press in the lock-off button and then pull
the trigger. Release the trigger to stop.
Kerf board (Fig. 15)
This tool is provided with the kerf board in the turn base.
If the kerf groove has not yet been cut in the kerf board by
the factory, you should cut the groove before actually
using the tool to cut a workpiece. Switch on the tool and
lower the blade gently to cut a groove in the kerf board.
Sub-fence (Fig. 16 & 17)
This tool is equipped with the sub-fence which should
ordinarily be positioned as shown in
Fig. 16 . However,
when performing left bevel cuts, set it to the left position
as shown in
Fig. 17 .
Maintaining maximum cutting capacity
(Fig. 18 & 19)
Unplug the tool before any adjustment is attempted. This
tool is factory adjusted to provide the max. cutting capac-
ity for a 260 mm saw blade. When the diameter of the
blade has been reduced due to sharpening, adjust the
depth adjusting bolt by turning it with the socket wrench.
The saw blade is lowered by turning the depth adjusting
bolt counterclockwise and raised by turning it clockwise.
Adjust so that when the handle is in the fully lowered
position, there will be a distance of about 135 mm from
the front face of the guide fence to the point where the
front edge of the blade enters the kerf. With the tool
unplugged, rotate the blade by hand while holding the
handle all the way down. Be sure that the blade does not
contact any part of the lower base when the handle is
lowered completely.
Positioning for adjusting the miter angle (Fig. 20)
Loosen the grip by turning counterclockwise. Turn the
turn base while pressing down the latch spring. When
you have moved the grip to the position where the pointer
indicates the desired angle on the miter scale, securely
tighten the grip clockwise.
CAUTION:
When turning the turn base, be sure to raise the handle
fully.
Positioning for adjusting the bevel angle
(Fig. 21 & 22)
The saw blade tilts up to 45° to the left only when the
sub-fence is set to the left position as shown in
Fig. 17 .
To adjust the bevel angle, loosen the lever at the rear of
the tool. Tilt the blade to the left so that the pointer indi-
cates the desired angle on the bevel scale. Then tighten
the lever firmly to secure the arm.
CAUTION:
When tilting the saw blade, be sure to raise the handle
fully.
Securing workpiece
WARNING:
It is extremely important to always secure the workpiece
properly and tightly with the vise. Failure to do so can
cause the tool to be damaged and/or the workpiece to be
destroyed. PERSONAL INJURY MAY ALSO RESULT.
Also, after a cutting operation, DO NOT raise the blade
until the blade has come to a complete stop.
1. Vertical vise (Fig. 23 & 27)
The vertical vise can be installed on the guide
fence or the holder assembly (optional accessory).
Insert the vise rod into the hole in the guide fence or
the holder assembly and tighten the screw to secure
the vise rod. Position the vise arm according to the
thickness and shape of the workpiece and secure
the vise arm by tightening the screw. Press the
workpiece flat against the guide fence and the turn
base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the clamp
screw.