background image

[4] ADJUSTMENT
[4]-3. Guide fence

1) Pretighten M8x25 Hex socket head bolt (with flat washer and spring washer) at the threaded hole designated with gray 
     arrow. The round shape around the thread hole is smaller than the others (designated with black arrow) for M8x25 Hex 
     socket head bolts.
2) Do fine adjustment of the right angle between Blade and Guide fence using 1R208.
3) Tighten M8x25 Hex socket head bolt (4pcs.) in order 1, 2, 3, and 4. without moving any parts. (Fig. 73)  

  Use 1R208 and M8x20 Hex socket head bolt on Arm holder complete to adjust 90 degree angle between Blade and 
  Turn base. (Fig. 74)
  Use 1R207 and M8x20 Hex socket head bolts on the right side and the left side of Arm complete to adjust 45 degree 
  angle between Blade and Turn base. (Fig. 75)
Note: When tilting the carriage to the right, tilt the carriage to the left slightly after loosening the lever and press Release
          button. Tilting the carriage to the left can be done without pushing Release button. 
  Adjust Maximum cutting depth as follows;
  1) Lower Stopper lever to position Blade as shown in Fig. 76.
  2) Push the carriage toward Guide fence fully and lower Handle completely. (Fig. 76)
  3) Use the hex end of 782232-8 to turn M8x20 Hex socket head bolt until the periphery of Blade extends slightly below 
      the top surface of Turn base and adjust Blade so that the tip is placed as illustrated in Fig. 77.  

Fig. 73

P 2

4/ 37

R

epair

Fig. 74

Fig. 75

Fig. 76

Pretighten M8x25
Hex socket head bolt  

Blade

Arm holder complete

Arm complete

1R208

Guide plate

1

2

3

4

[4]-4. Blade

M8x20 Hex socket head bolt
for 90 degree angle adjusting

M8x20 Hex socket head 
bolt for 45 degree angle adjusting

Fig. 77

Triangle mark
on Kerf board

255mm
Blade tip

Triangle mark on Kerf board

260mm
Blade tip

4mm

Release button

Stopper lever

Hex end

Carriage
(gray portion)

M8x20 Hex socket head bolt
on Blade case complete 

782232-8

Summary of Contents for LS1016






































Reviews: