background image

17 

1

2

3

 

 

015133 

2. Bevel 

angle 

1

3

2

 

 

012221 

(1)  0° bevel angle 

Lower the handle fully and lock it in the 
lowered position by pushing in the stopper 
pin. Loosen the lever at the rear of the tool. 
Turn the 0° bevel angle adjusting bolt on the 
right side of the turn base two or three 
revolutions clockwise to tilt the blade to the 
right. 
Carefully square the side of the blade with 
the top surface of the turn base using the 
triangular rule, try-square, etc. by turning the 
0° bevel angle adjusting bolt 
counterclockwise.  

1

2

3

 

 

010798 

Make sure that the pointer on the turn base 
point to 0° on the bevel scale on the arm. If it 
does not point to 0°, loosen the screw which 
secures the pointer and adjust the pointer so 
that it will point to 0°. 

1

2
3
4

 

 

012222 

(2)  45° bevel angle 

4
1

2

3

 

 

012223 

Adjust the 45° bevel angle only after 
performing 0° bevel angle adjustment. To 
adjust left 45° bevel angle, loosen the lever 
and tilt the blade to the left fully. Make sure 
that the pointer on the arm points to 45° on 
the bevel scale on the arm. If the pointer does 
not point to 45°, turn the 45° bevel angle 
adjusting bolt on the left side of the arm until 
the pointer points to 45°. 

Replacing carbon brushes 

   

007834 

Remove and check the carbon brushes regularly. 
Replace when they wear down to 3mm in length. Keep 
the carbon brushes clean and free to slip in the holders. 
Both carbon brushes should be replaced at the same 
time. Use only identical carbon brushes. 
Use a screwdriver to remove the brush holder caps. 
Take out the worn carbon brushes, insert the new ones 
and secure the brush holder caps. 

1. Triangular rule
2. Saw blade 
3. Top surface of 

turn base 

1. Triangular rule
2. Grip 
3. Guide fence 

1. Lever 
2. Arm 
3. Pointer 
4. 45

bevel angle 

adjusting bolt 

1. Arm 
2. Bevel scale 
3. Pointer 
4. Turn base 

1. Turn base 
2. Lever 
3. 0

 adjusting 

bolt 

Summary of Contents for LH1201FL/2





















Reviews: