background image

16 ENGLISH

Guide rail

Optional accessory

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before loosening the adjusting screws on the tool 

base.

NOTICE:

 Remove the sub base when using the 

guide rail.

Place the tool on the rear end of guide rail. Turn two 

adjusting screws on the tool base so that the tool slides 

smoothly without a clatter. Hold both the front grip and 

rear handle of the tool firmly. Install the battery car

-

tridge. Turn on the tool and cut the splinter-guard along 

the full length with a stroke. Now the edge of the splin-

ter-guard corresponds to the cutting edge.

1

Fig.32

►    

1.

 Adjusting screws

When bevel cutting with the guide rail, use the slide 

lever to prevent the tool from falling over.

Move the slide lever on the tool base in the direction 

of arrow so that it engages the undercut groove in the 

guide rail.

1

Fig.33

►    

1.

 Slide lever

WIRELESS ACTIVATION 

FUNCTION

What you can do with the wireless 

activation function

The wireless activation function enables clean and com-

fortable operation. By connecting a supported vacuum 

cleaner to the tool, you can run the vacuum cleaner 

automatically along with the switch operation of the tool.

Fig.34

To use the wireless activation function, prepare follow-

ing items:

• 

A wireless unit (optional accessory)

• 

A vacuum cleaner which supports the wireless 

activation function

The overview of the wireless activation function 

setting is as follows. Refer to each section for detail 

procedures.

1.

  Installing the wireless unit

2.

  Tool registration for the vacuum cleaner

3.

  Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION:

 

Place the tool on a flat and stable 

surface when installing the wireless unit.

NOTICE:

 

Clean the dust and dirt on the tool 

before installing the wireless unit.

 Dust or dirt 

may cause malfunction if it comes into the slot of the 

wireless unit.

NOTICE:

 

To prevent the malfunction caused by 

static, touch a static discharging material, such 

as a metal part of the tool, before picking up the 

wireless unit.

NOTICE:

 

When installing the wireless unit, 

always be sure that the wireless unit is inserted 

in the correct direction and the lid is completely 

closed.

Summary of Contents for HS009GZ

























Reviews: