background image

R

epair

P 7 / 19

< 5 > Assembling change lever
         1. Apply grease to the pin of change lever and O ring 17 referring to < 1 > Lubrication at page 5.
         2. Assemble compression spring 3 and lock button to change lever. And temporarily assemble cap to the position 
             illustrated in Fig. 3 in order to stop springing off of  lock button. Do not forget to assemble O ring 17. See Fig. 3.
         3. Insert the change lever in which compression spring 3 and lock button have been temporarily fixed with cap, into
             the assembling hole of gear housing.  See Fig. 3A.  The change lever can not be inserted completely in this stage.
         4. Pressing the change lever, turn it in the direction of drill mode. Then, it can be inserted completely 
             in any position of area B.  See Fig. 3B.  
         5. Turn the change lever to the area C.  See Fig. 3B. And assemble cap completely to the original position 
             of change lever, by pressing to gear housing side.

< 4 > Disassembling change lever
         1. Separate cap from change lever.  See Fig. 1.
         2. Fully  turn change lever in the direction of drill mode. Then, change lever can be pulled out from gear housing.
             See Fig. 2A and Fig. 2B

Cap

Gear housing

Cap

Gear housing

Gear housing

Lock button

Compression spring 3

Fig. 2

Fig. 2A

Fig. 2B

Fig. 2C

 Change lever

O ring 17

< Note >
Be careful, not to lose lock button and compression spring 3. 
They  can easily spring off.  See Fig. 2C.

Cap

Change lever

Change lever

Change lever

Compression spring 3

Lock button

Cap assembled 
temporarily 

Cap assembled 
completely by 
pressing. 

 Lock button

 Lock button

Compression 
spring 3

Fig. 3

Fig. 3A

Fig. 3B

O ring 17

A

Insert the change lever 
within the area A.

B

If the change lever can not be inserted completely 
in any position of area B, pressing lock button, turn it to the direction 
of drill mode again in order to insert completely in any position of area B.

C

Compression 
spring 3

Summary of Contents for HR2452




















Reviews: