Makita HP330DWE Instruction Manual Download Page 6

Page: 6 / 60

Reversing switch action (Fig. 4)

This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation
before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

Speed change (Fig. 5)

To change the speed, first switch off the tool and then
slide the speed change lever to the “2” side for high speed
or “1” side for low speed. Be sure that the speed change
lever is set to the correct position before operation. Use
the right speed for your job.

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change
lever positioned halfway between the “1” side and “2”
side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Selecting the action mode (Fig. 6)

This tool employs an action mode changing ring. Select
one of the three modes suitable for your work needs by
using this ring.
For rotation only, turn the ring so that the arrow on the tool
body points toward the   mark on the ring.
For rotation with hammering, turn the ring so that the
arrow points toward the   mark on the ring.
For rotation with clutch, turn the ring so that the arrow
points toward the   mark on the ring.

CAUTION:

• When you change the position from “ ” to other

modes, it may be a little difficulty to slide the action
mode changing ring. In this case, switch on and run the
tool for a second at the “ ” position, then stop the tool
and slide the ring to your desired position.

• Always set the ring correctly to your desired mode

mark. If you operate the tool with the ring positioned
halfway between the mode marks, the tool may be
damaged.

Adjusting the fastening torque (Fig. 7)

The fastening torque can be adjusted in 18 steps by
turning the adjusting ring so that the graduations are
aligned with the arrow on the tool body. The fastening
torque is minimum when the number 1 is aligned with the
arrow, and maximum when the number 18 is aligned with
the arrow.
Before the actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.

NOTE:

• The fastening torque can be adjusted only when the

arrow points toward the mark on the ring.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any
work on the tool.

Installing or removing driver bit or drill bit
(Fig. 8)

Turn the sleeve counterclockwise to open the chuck jaws.
Place the bit in the chuck as far as it will go. Turn the
sleeve clockwise to tighten the chuck.
To remove the bit, turn the sleeve counterclockwise.

OPERATION (Fig. 9)

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. Otherwise, it may accidentally fall out of
the tool, causing injury to you or someone around you.

Hold the tool firmly with one hand on the grip and the
other hand on the bottom of the battery cartridge to
control the twisting action.

CAUTION:

• Do not cover vents, or it may cause overheating and

damage to the tool.

Hammer drilling operation

CAUTION:

• There is a tremendous and sudden twisting force

exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with chips
and particles, or when striking reinforcing rods
embedded in the concrete.

First, turn the action mode changing ring so that the arrow
on the tool body points to the marking. The adjusting
ring can be aligned in any torque levels for this operation.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.

Blow-out bulb (optional accessory)
(Fig. 10)

After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.

Drilling operation

First, turn the adjusting ring so that the pointer points to
the marking. Then proceed as follows.