9
ENGLISH
14.
Keep fingers away from switch trigger when
not operating the tool and when moving from
one operating position to another.
Intended use of the tool
1.
Use right tool. The cordless grass trimmer is
only intended for cutting grass, light weeds. It
should not be used for any other purpose such
as hedge cutting as this may cause injury.
Personal protective equipment
►
Fig.1
►
Fig.2
1.
Dress Properly. The clothing worn should be
functional and appropriate, i.e. it should be
tight-fitting but not cause hindrance. Do not
wear either jewelry or clothing which could
become entangled with high grass. Wear pro-
tective hair covering to contain long hair.
2.
When using the tool, always wear sturdy shoes
with a non-slip sole. This protects against
injuries and ensures a good footing.
3.
Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
Electrical and battery safety
1.
Avoid dangerous environment. Don't use the
tool in damp or wet locations or expose it to
rain. Water entering the tool will increase the
risk of electric shock.
2.
Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
fire when used with another battery pack.
3.
Use power tools only with specifically desig
-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
4.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fire.
5.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6.
Do not dispose of the battery(ies) in a fire. The
cell may explode. Check with local codes for
possible special disposal instructions.
7.
Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be
toxic if swallowed.
8.
Do not charge battery in rain, or in wet
locations.
Starting up the tool
►
Fig.3
1.
Make sure that there are no children or other
people within a working range of 15 meters
(50 ft), also pay attention to any animals in the
working vicinity. Otherwise stop using the tool.
2.
Before use always check that the tool is safe
for operation. Check the security of the cutting
tool and the guard and the switch trigger/lever
for easy and proper action. Check for clean
and dry handles and test the on/off function of
the switch.
3.
Check damaged parts before further use of
the tool. A guard or other part that is damaged
should be carefully checked to determine
that it will operate properly and perform its
intended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other condition that
may affect its operation. A guard or other part
that is damaged should be properly repaired
or replaced by our authorized service center
unless indicated elsewhere in this manual.
4.
Switch on the motor only when hands and feet
are away from the cutting tool.
5.
Before starting make sure that the cutting
tool has no contact with hard objects such as
branches, stones etc. as the cutting tool will
revolve when starting.
6.
Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Method of operation
1.
Never operate the machine with damaged
guards or without the guards in place.
2.
Only use the tool in good light and visibility.
During the winter season beware of slippery
or wet areas, ice and snow (risk of slipping).
Always ensure a safe footing.
3.
Take care against injury to feet and hands from
the cutting tool.
4.
Keep hands and feet away from the cutting
means at all times and especially when switch-
ing on the motor.
5.
Never cut above waist height.
6.
Never stand on a ladder and run the tool.
7.
Never work on unstable surfaces.
8.
Don't overreach. Keep proper footing and
balance at all times.
Summary of Contents for DUR189RF
Page 2: ...Fig 1 Fig 2 Fig 3 2 3 1 6 7 8 9 10 11 12 13 12 4 5 Fig 4 2 ...
Page 3: ...1 2 3 Fig 5 1 2 Fig 6 1 Fig 7 2 1 Fig 8 1 Fig 9 1 Fig 10 1 Fig 11 1 2 Fig 12 3 ...
Page 4: ...1 2 3 4 5 Fig 13 Fig 14 1 3 1 4 2 4 3 3 2 Fig 15 1 2 2 1 Fig 16 Fig 17 1 2 Fig 18 4 ...
Page 5: ...Fig 19 6 5 1 2 3 4 Fig 20 1 2 3 4 5 Fig 21 1 Fig 22 Fig 23 2 1 Fig 24 1 Fig 25 5 ...
