background image

2

ENGLISH

SPECIFICATIONS

Model:

DUH506

DUH606

Blade length

500 mm

600 mm

Strokes per minute

4,000 min

-1

Overall length
(Without battery)

846 mm

965 mm

Rated voltage

D.C. 18 V

Net weight

2.5 - 2.9 kg

2.7 - 3.0 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications may differ from country to country.

• 

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi

-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge

BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger

DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / 

DC18SH / DC18WC

• 

Some of the battery cartridges and chargers listed above may not be available depending on your region of 
residence.

WARNING:

 

Only use the battery cartridges and chargers listed above.

 Use of any other battery cartridges 

and chargers may cause injury and/or fire.

Recommended cord connected power source

Portable power pack

PDC01

• 

The cord connected power source(s) listed above may not be available depending on your region of residence.

• 

Before using the cord connected power source, read instruction and cautionary markings on them.

Symbols

The followings show the symbols which may be used 
for the equipment. Be sure that you understand their 
meaning before use.

 

Read instruction manual.

Wear eye protection.

DANGER - Keep hands away from blade.

Do not expose to moisture.

 

Ni-MH

Li-ion

Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical 
and electronic equipment, accumulators 
and batteries may have a negative impact 
on the environment and human health.
Do not dispose of electrical and electronic 
appliances or batteries with household 
waste!
In accordance with the European Directive 
on waste electrical and electronic equip-
ment and on accumulators and batteries 
and waste accumulators and batteries, 
as well as their adaptation to national law, 
waste electrical equipment, batteries and 
accumulators should be stored separately 
and delivered to a separate collection point 
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the 
crossed-out wheeled bin placed on the 
equipment.

Guaranteed sound power level according 
to EU Outdoor Noise Directive.

Sound power level according to Australia 
NSW Noise Control Regulation.

Intended use

The tool is intended for trimming hedges.

Summary of Contents for DUH606ST





















Reviews: