15 ENGLISH
Switch action
WARNING:
For your safety, this tool is
equipped with lock-off lever which prevents the
tool from unintended starting. NEVER use the tool
if it runs when you simply pull the switch trigger
without pressing the lock-off lever. Return the
tool to our authorized service center for proper
repairs BEFORE further usage.
WARNING:
NEVER tape down or defeat pur
-
pose and function of lock-off lever.
CAUTION:
Before installing the battery car
-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the “OFF” position when released.
NOTICE:
Do not pull the switch trigger hard with
-
out pressing the lock-off lever. This can cause
switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided. To start the tool,
depress the lock-off lever and pull the switch trigger.
Release the switch trigger to stop.
►
Fig.5:
1.
Switch trigger
2.
Lock-off lever
Checking the run-down brake
CAUTION:
If the saw chain does not stop
within a few seconds in this test, stop using the
tool and consult our authorized service center.
Run the tool, and then release the switch trigger com
-
pletely. The saw chain must come to a standstill within
a few seconds.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Do not touch the saw chain with
bare hands. Always wear gloves when handling
the saw chain.
Removing or installing saw chain
CAUTION:
The saw chain and the guide bar
are still hot just after the operation. Let them cool
down enough before carrying out any work on
the tool.
CAUTION:
Carry out the procedure of install
-
ing or removing saw chain in a clean place free
from sawdust and the like.
Removing the saw chain
To remove the saw chain, perform the following steps:
1.
Pull the lever up.
►
Fig.6:
1.
Lever
2.
Turn the lever counterclockwise until the sprocket
cover comes off.
►
Fig.7:
1.
Sprocket cover
2.
Lever
3.
Remove the sprocket cover then remove the saw
chain and guide bar from the tool body.
Installing the saw chain
To install the saw chain, perform the following steps:
1.
Pull the lever up.
►
Fig.8:
1.
Lever
2.
Turn the lever counterclockwise until the sprocket
cover comes off.
►
Fig.9:
1.
Lever
2.
Sprocket cover
3.
Remove the sprocket cover.
4.
Align the hole on the guide bar with the pin on the
tool body, and then place the guide bar as shown in the
figure.
►
Fig.10:
1.
Guide bar
2.
Hole
3.
Pin
5.
Slide the guide bar toward the sprocket to lock the
pin.
►
Fig.11:
1.
Guide bar
2.
Pin
6.
Remove the guide bar from the tool body.
7.
Check the direction of the saw chain. Match the
direction of the saw chain with that of the mark on the
tool body.
►
Fig.12:
1.
Mark on tool body
8.
Fit one end of the saw chain on the top of the
guide bar.
9.
Fit the other end of the saw chain around the
sprocket, then attach the guide bar to the tool body so
that the hole on the guide bar is aligned with the pin on
the body.
►
Fig.13:
1.
Sprocket
Press the guide bar against the tool body to release the
pin. The saw chain tension is automatically adjusted.
►
Fig.14:
1.
Saw chain
2.
Pin
3.
Sprocket
10.
Place the sprocket cover so that the bolt and pin
on the tool body meet their counterparts on the sprocket
cover.
►
Fig.15:
1.
Sprocket cover
2.
Bolt
3.
Pin
11.
Turn the lever clockwise until the sprocket cover is
secured then return it to the original position.
►
Fig.16:
1.
Lever
2.
Sprocket cover
Make sure that the saw chain does not loose and the
saw chain can be moved smoothly back and forth. If
necessary, adjust the tension of the saw chain by refer
-
ring to the section for adjusting saw chain tension.
Summary of Contents for DUC101Z
Page 2: ...2 Fig 1 1 2 3 4 5 7 8 10 11 9 6 12 Fig 2 1 3 2 Fig 3 1 2 Fig 4 ...
Page 3: ...3 1 2 Fig 5 1 Fig 6 2 1 Fig 7 1 Fig 8 1 2 Fig 9 1 3 2 Fig 10 ...
Page 4: ...4 1 2 Fig 11 1 Fig 12 1 Fig 13 1 2 3 Fig 14 1 3 2 Fig 15 1 2 Fig 16 1 Fig 17 2 1 Fig 18 ...
Page 5: ...5 1 2 Fig 19 1 2 Fig 20 1 2 3 Fig 21 2 1 Fig 22 Fig 23 Fig 24 ...
