8 ENGLISH
Impact force grade displayed on
panel
Maximum blows
Application
DTW1001
DTW1002
DTW800
Soft
1,800 min
-1
(/min)
Tightening when you need fine adjustment with
small diameter bolt.
Impact force/bolt size corresponding chart (reference)
Impact force grade displayed on
panel
DTW1001
DTW1002
DTW800
Standard bolt High tensile
bolt
Standard bolt High tensile
bolt
Standard bolt High tensile
bolt
Hard
M20 - M30
(3/4″ - 1-1/4″)
M16 - M24
(5/8″ - 1″)
M20 - M30
(3/4″ - 1-1/4″)
M16 - M24
(5/8″ - 1″)
M20 - M24
(3/4″ - 1″)
M16 - M22
(5/8″ - 7/8″)
Medium
M16 - M24
(5/8″ - 1″)
M12 - M20
(1/2″ - 3/4″)
M16 - M24
(5/8″ - 1″)
M12 - M20
(1/2″ - 3/4″)
M14 - M20
(9/16″ - 3/4″)
M10 - M16
(3/8″ - 5/8″)
Soft
M12 - M20
(1/2″ - 3/4″)
M10 - M16
(3/8″ - 5/8″)
M12 - M20
(1/2″ - 3/4″)
M10 - M16
(3/8″ - 5/8″)
M12 - M16
(1/2″ - 5/8″)
M10 - M12
(3/8″ - 1/2″)
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct impact socket
Always use the correct size impact socket for bolts and
nuts. An incorrect size impact socket will result in inac
-
curate and inconsistent fastening torque and/or damage
to the bolt or nut.
Installing or removing impact socket
Only for Model DTW1001,DTW1002 (optional
accessory)
CAUTION:
Make sure that the impact socket
and the mounting portion are not damaged before
installing the impact socket.
For impact socket without O-ring
and pin
►
Fig.9:
1.
Impact socket
2.
Square drive
Align the square of the impact socket with the square
drive and push the impact socket onto the square drive
until it locks into place. Tap it lightly if required.
To remove the impact socket, simply pull it off.
For impact socket with O-ring
and pin
Only for Model DTW1001
►
Fig.10:
1.
Impact socket
2.
O-ring
3.
Pin
Move the O-ring out of the groove in the impact socket
and remove the pin from the impact socket. Fit the
impact socket onto the square drive so that the hole in
the impact socket is aligned with the hole in the square
drive.
Insert the pin through the hole in the impact socket and
square drive. Then return the O-ring to the original posi
-
tion in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
Installing or removing drill bit/
socket adapter
Only for Model DTW800 (optional accessory)
►
Fig.11
A=11.2 mm
Use only the drill bit/socket adapter shown in the figure.
Do not use any other drill bit/socket adapter.
►
Fig.12:
1.
Drill bit
2.
Sleeve
To install the drill bit, pull the sleeve in the direction of
the arrow and insert the drill bit into the sleeve as far as
it will go.
Then release the sleeve to secure the drill bit.
To remove the drill bit, pull the sleeve in the direction of
the arrow and pull the drill bit out.
