Makita DTL063Z, Instruction Manual

Page: 4 / 52

4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model DTL062 DTL063
Capacities Standard bolt M4 - M12 M4 - M12
High tensile bolt M4 - M8 M4 - M8
Square drive 9.5 mm 9.5 mm
No load speed (min
-1
) 0 - 2,000 0 - 2,000
Impacts per minute 0 - 3,000 0 - 3,000
Max. fastening torque 60 N•m 60 N•m
Overall length 387 mm 387 mm
Net weight 1.4 - 1.8 kg 1.4 - 2.0 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi -
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge D.C.14.4 V Model BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
D.C.18 V Model BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord -
ing to EN62841:
Sound pressure level (L
pA
) : 88 dB (A)
Sound power level (L
WA
) : 99 dB (A)
Uncertainty (K) : 3 dB (A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DTL062
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
h
) : 14.5 m/s
2
Uncertainty (K) : 2.0 m/s
2
Model DTL063
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
h
) : 16.5 m/s
2
Uncertainty (K) : 2.0 m/s
2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.