8 ENGLISH
Procedure 2
In addition to
Procedure 1
, insert the bit-piece into the
sleeve with its pointed end facing in.
►
Fig.9:
1.
Driver bit
2.
Bit-piece
3.
Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE:
If the driver bit is not inserted deep enough into the
sleeve, the sleeve will not return to its original position and
the driver bit will not be secured. In this case, try re-insert
-
ing the bit according to the instructions above.
NOTE:
When it is difficult to insert the driver bit, pull the
sleeve and insert it into the sleeve as far as it will go.
NOTE:
After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.
Installing hook
CAUTION:
When installing the hook, always
secure it with the screw firmly.
If not, the hook may
come off from the tool and result in the personal injury.
CAUTION:
Use the hanging/mounting parts
for their intended purposes only.
Using for unin-
tended purpose may cause accident or personal
injury.
►
Fig.10:
1.
Groove
2.
Hook
3.
Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
OPERATION
►
Fig.11
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in the figures.
Proper fastening torque for standard bolt
120
100
80
60
40
20
M14
M12
M10
M8
N•m
2
1
(kgf•cm)
(1224)
(1020)
(816)
(612)
(408)
(204)
0
140
(1428)
1
2
3
M16
M16
M14
M12
M10
M8
1.
Fastening time (second)
2.
Fastening torque
Proper fastening torque for high tensile bolt
0
1
2
3
M12
M10
160
(1632)
140
(1428)
120
(1224)
100
(1020)
80
(816)
60
(612)
40
(408)
20
(204)
M8
M12
M10
M8
N•m
(kgf•cm)
2
1
1.
Fastening time (second)
2.
Fastening torque
Hold the tool firmly and place the point of the driver bit
in the screw head. Apply forward pressure to the tool to
the extent that the bit will not slip off the screw and turn
the tool on to start operation.
NOTICE:
If you use a spare battery to continue
the operation, rest the tool at least 15 min.
NOTE:
Use the proper bit for the head of the screw/
bolt that you wish to use.
NOTE:
When fastening M8 or smaller screw, carefully
adjust pressure on the switch trigger so that the screw
is not damaged.
NOTE:
Hold the tool pointed straight at the screw.
NOTE:
If the impact force is too strong or you tighten
the screw for a time longer than shown in the figures,
the screw or the point of the driver bit may be over
-
stressed, stripped, damaged, etc. Before starting your
job, always perform a test operation to determine the
proper fastening time for your screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1. When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3. Bolt
•
Even though the torque coefficient and the
class of bolt are the same, the proper fasten-
ing torque will differ according to the diame
-
ter of bolt.
•
Even though the diameters of bolts are the
same, the proper fastening torque will differ
according to the torque coefficient, the class
of bolt and the bolt length.
4. The manner of holding the tool or the material
of driving position to be fastened will affect the
torque.
5. Operating the tool at low speed will cause a reduc-
tion in the fastening torque.
