21 ENGLISH
3.
Operate the tool in the same way as the straight
guide for the trimmer base.
►
Fig.66
Using the templet guide
Optional accessory
1.
Loosen the screws on the base and remove them.
Place the templet guide on the base, and then tighten
the screws.
►
Fig.67:
1.
Screw
2.
Templet guide
2.
Operate the tool in the same way as the templet
guide for the trimmer base.
►
Fig.68
Using the parallel ruler
The parallel ruler is effectively used for straight cuts
when chamfering or grooving. Adjust the distance
between the bit and the parallel ruler. At the desired
distance, tighten the wing bolts to secure the parallel
ruler. When cutting, move the tool with the parallel ruler
flush with the side of the workpiece.
►
Fig.69
If the distance (A) between the side of the workpiece
and the cutting position is too wide for the parallel ruler,
or if the side of the workpiece is not straight, the parallel
ruler cannot be used.
In this case, firmly clamp a straight board to the work
-
piece and use it as a guide against the plunge base.
Feed the tool in the direction of the arrow.
►
Fig.70
Changing knob type grip to bar type
grip
To install the bar type grip on the plunge base, loosen
the screw of the knob type grip, then remove the knob
type grip, and then install the bar type grip by tightening
it.
►
Fig.71:
1.
Knob type grip
2.
Screw
3.
Bar type grip
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
•
Straight and groove forming bits
•
Edge forming bits
•
Laminate trimming bits
•
Straight guide assembly
•
Trimmer guide assembly
•
Trimmer base assembly
•
Trimmer base assembly (resin)
•
Tilt base assembly
•
Plunge base assembly
•
Offset base assembly
•
Grip attachment
•
Templet guide
•
Collet cone
•
Wrench 13
•
Wrench 22
•
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
Trimmer bits
Straight bit
►
Fig.72
D
A
L1
L2
20
6
20
50
15
20E
1/4"
8
8
8
60
25
8
6
50
18
8E
1/4"
6
6
6
50
18
6E
1/4"
Unit: mm
"U" Grooving bit
►
Fig.73
D
A
L1
L2
R
6
6
6
50
18
3
6E
1/4"
Unit: mm
Summary of Contents for DRT50ZJX9
