7
OPERATION
Driving pin nails
WARNING:
• Before pulling the trigger, always make sure that the
opening that pin-nails are fired contacts material to be
fastened. Just pulling the trigger fires pin nails.
Misfiring may cause personal injuries.
(Fig. 13)
Place flat the opening of the tool that pin-nails are fired on
the material to be fastened and hold the tool firmly against
the material. Then pull the lever and then pull the trigger
fully to drive the pin nail. The grip is shaped so that the
tool head can be held down securely with index finger and
thumb. After driving a pin-nail, be sure to release the
trigger fully.
(Fig. 14)
When the head of driven pin-nail remains above the
surface of the material, drive the pin-nail while holding the
pin nailer head firmly.
NOTE:
• When the trigger is pulled after a quick trigger action,
the nailer may do nothing but operates momentarily
and may not fire pin nails. This is not a trouble. At this
time, release the trigger once, pull it again and the pin
nails can be fired.
• Using the pin nailer continuously with the head of fired
pin nails remaining above the surface of material to be
fastened may cause damage to the driver of the pin
nailer and nailer jamming etc.
Removing jammed pin nails
WARNING:
• Always make sure that the lever is released and the
battery cartridge is removed before removing jammed
nails.
(Fig. 15)
Remove the battery cartridge from the pin nailer.
Take out pin nails that remain inside the magazine.
Loosen bolt (A) and bolt (B) by turning them
approximately two turns using the hex wrench provided
with the pin nailer.
Remove driver guide cover by sliding it.
Remove stuck pin nails, debris, adhesives and woodchips
etc. from the passage for pin nails.
Check the driver guide cover for stuck pin nails or other
foreign matters and then secure it with these two bolts.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
• To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized Service Centers,
always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Pin nails
• Various type of Makita genuine batteries and chargers
• Safety goggles
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
ENG905-1
The typical A-weighted noise level determined according
to EN60745:
Model DPT350
Sound pressure level (L
pA
): 75 dB (A)
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DPT351
Sound pressure level (L
pA
): 74 dB (A)
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
ENG904-2
The vibration emission value determined according to
EN60745:
Vibration emission (a
h
): 2.5 m/s
2
or less
Uncertainty (K): 1.5 m/s
2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
ENH101-15
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Pin Nailer
Model No./ Type: DPT350, DPT351
are of series production and
Conforms to the following European Directives:
2006/42/EC