background image

22 ENGLISH

Workpieces up to 68 mm high and 160 mm wide can be 

cut in the following manner.

1

►    

1.

 Stopper pin

1.

 

Push the carriage toward the guide fence until it 

stops and lock it with the stopper pin.

2.

 

Secure the workpiece with the proper type of vise.

3.

 

Switch on the tool without the blade making any 

contact and wait until the blade attains full speed before 

lowering.

4.

 

Gently lower the handle to the fully lowered posi-

tion to cut the workpiece.

5.

 

When the cut is completed, switch off the tool and 

wait until the blade has come to a complete stop

 

before returning the blade to its fully elevated position.

Slide (push) cutting (cutting wide 

workpieces)

WARNING:

 

Whenever performing a slide cut, 

first pull the carriage full towards you and press 

the handle all the way down, then push the car-

riage toward the guide fence. Never start the cut 

with the carriage not pulled fully toward you.

 If 

you perform the slide cut without the carriage pulled 

fully toward you unexpected kickback may occur and 

serious personal injury may result.

WARNING:

 

Never attempt to perform a slide 

cut by pulling the carriage towards you.

 Pulling 

the carriage towards you while cutting may cause 

unexpected kickback resulting in possible serious 

personal injury.

WARNING:

 

Never perform the slide cut with 

the handle locked in the lowered position.

1

►    

1.

 Stopper pin

1.

 

Unlock the stopper pin so that the carriage can 

slide freely.

2.

 

Secure the workpiece with the proper type of vise.

3.

 

Pull the carriage toward you fully.

4.

 

Switch on the tool without the blade making any 

contact and wait until the blade attains full speed.

5.

 

Press the handle down and 

push the carriage 

toward the guide fence and through the workpiece.
6.

 

When the cut is completed, switch off the tool and 

wait until the blade has come to a complete stop

 

before returning the blade to its fully elevated position.

Miter cutting

Refer to the previously covered "Adjusting the miter 

angle".

Summary of Contents for DLS112

































Reviews: