17 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
DLS110
DLS111
DLS112
Blade diameter
European countries
260 mm
Countries other than Europe
255 mm - 260 mm
Hole diameter
European countries
30 mm
Countries other than Europe
25.4 mm
Max. kerf thickness of the saw blade
3.2 mm
Max. miter angle
Right 60°, Left 60°
Max. bevel angle
Right 48°, Left 48°
No load speed (RPM)
4,400 min
-1
Laser type
-
Red Laser 650 nm, Maximum output
1.6mW ( Laser Class 2M )
Rated voltage
D.C. 36 V
Battery cartridge
BL1815N, BL1820, BL1820B, BL1830, BL1830B, BL1840,
BL1840B, BL1850, BL1850B, BL1860B
Charger
DC18RC, DC18RD, DC18SD, DC18SE, DC18SF
Dimensions (L x W x H)
805 mm x 644 mm x 660 mm
Net weight
26.6 - 27.3 kg
Cutting capacities (H x W)
Miter angle
Bevel angle
45° (left)
0°
45° (right)
0°
42 mm x 310 mm
58 mm x 279 mm
68 mm x 310 mm
91 mm x 279 mm
29 mm x 310 mm
43 mm x 279 mm
45° (right and left)
42 mm x 218 mm
58 mm x 197 mm
68 mm x 218 mm
91 mm x 197 mm
29 mm x 218 mm
43 mm x 197 mm
60° (right and left)
-
68 mm x 155 mm
91 mm x 139 mm
-
Cutting capacities for special cuttings
Type of cutting
Cutting capacity
Crown molding 45° type
(with crown molding stopper used)
168 mm
Base board
(with horizontal vise used)
133 mm
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications and battery cartridge may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
To avoid injury from flying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
1
2
3
When performing bevel cut, first turn the
knob counterclockwise and then tilt the
carriage. After that, turn the knob clockwise
to tighten.
When performing slide cut, first pull car
-
riage fully and press down handle, then
push carriage toward the guide fence.
Hold down the releasing button when tilting
the carriage to the right.
Engage the stopper lever when cutting a
base board in 45° miter angle.
Summary of Contents for DLS111ZU
