background image

14 ENGLISH

For tool with the inner flange for a 

15.88 mm hole-diameter saw blade 

(country specific)

Mount the inner flange with its recessed side facing outward 

onto the mounting shaft and then place circular saw blade 

(with the ring attached if needed), outer flange and hex bolt.

For tool without the ring

1

2

3

4

5

►    

1.

 Mounting shaft 

2.

 Inner flange 

3.

 Circular saw 

blade 

4.

 Outer flange 

5.

 Hex bolt

For tool with the ring

1

2

3

4

5

6

15.88

15.88

15.88

►    

1.

 Mounting shaft 

2.

 Inner flange 

3.

 Circular saw 

blade 

4.

 Outer flange 

5.

 Hex bolt 

6.

 Ring

WARNING:

 

BE SURE TO TIGHTEN THE HEX 

BOLT CLOCKWISE SECURELY. Also be careful 

not to tighten the bolt forcibly. Slipping your hand 

from the hex wrench can cause a personal injury.

WARNING:

 

If the ring is needed to mount the 

blade onto the spindle, always be sure that the cor-

rect ring for the blade's arbor hole you intend to use 

is installed between the inner and the outer flanges.

 

Use of the incorrect arbor hole ring may result in the 

improper mounting of the blade causing blade move-

ment and severe vibration resulting in possible loss of 

control during operation and in serious personal injury.

Blade guard cleaning

When changing the circular saw blade, make sure to 

also clean the upper and lower blade guards of accu-

mulated sawdust as discussed in the Maintenance 

section. Such efforts do not replace the need to check 

lower guard operation before each use.

Connecting a vacuum cleaner

When you wish to perform clean cutting operation, 

connect a Makita vacuum cleaner to your tool. Connect 

a hose of the vacuum cleaner to the dust nozzle as 

shown in the figure.

1

2

►    

1.

 Dust nozzle 

2.

 Screw

2

1

►    

1.

 Hose 

2.

 Vacuum cleaner

OPERATION

This tool is intended to cut wood products. With appro-

priate Makita genuine circular saw blades, following 

materials can also be sawed:
• 

Aluminum products

Refer to our website or contact your local Makita dealer 

for the correct circular saw blades to be used for the 

material to be cut.

Checking blade guard function

Set the bevel angle to 0°, and then retract the lower 

guard manually to the end and release it. The lower 

guard is properly functioning if;
—  it is retracted above the base without any hin

-

drance and;

—  it automatically returns and contacts with the 

stopper.

Summary of Contents for DHS783ZJU

























Reviews: