11 ENGLISH
Using abrasive paper without dust-
suction hole
Optional accessory
1.
Cut a sheet of abrasive paper down to an appro
-
priate size.
►
Fig.6:
1.
Abrasive paper
2.
Pad
2.
Push and hold down the clamp lever on either
front or rear end of the pad, and slide it away from
the stopper so the clamp is released from its locked
position.
3.
Pull the clamp lever outwards as far as possible to
create a space between the clamp and side wall of the
sanding base in which one end of abrasive paper can
be inserted.
4.
Slip one end of the abrasive paper into the space
between the clamp and sanding base.
5.
Reposition the abrasive paper so it is finely over
-
laid on the pad surface.
6.
Set the clamp lever back in a locked position to
clamp the end of abrasive paper securely.
7.
Release the clamp on the other end, and have the
other end of abrasive paper ready to be clamped.
8.
Maintain a proper tension on abrasive paper, and
then set the clamp lever on the other end in a locked
position.
►
Fig.7:
1.
Abrasive paper
2.
Clamp
3.
Sanding base
4.
Clamp lever
5.
Stopper
9.
Cover the abrasive paper with the punch plate
with its positioning stoppers adjacent to the corner well
fit onto two of the side edges of the pad and sanding
base.
►
Fig.8:
1.
Abrasive paper
2.
Punch plate
3.
Positioning stoppers
4.
Pad
5.
Sanding
base
10.
Push the punch plate over the abrasive paper to
make dust-suction holes.
11.
To remove the abrasive paper, release the clamps
on both ends and take the paper off the pad.
Using abrasive paper with dust-
suction hole
Optional accessory
1.
Push and hold down the clamp lever on either
front or rear end of the pad, and slide it away from
the stopper so the clamp is released from its locked
position.
2.
Pull the clamp lever outwards as far as possible to
create a space between the clamp and side wall of the
sanding base in which one end of abrasive paper can
be inserted.
3.
Place a sheet of abrasive paper over the pad,
aligning the dust-suction holes in the paper with those
in the pad.
►
Fig.9:
1.
Abrasive paper
2.
Pad
3.
Dust-suction hole
4.
Slip one end of the abrasive paper into the space
between the clamp and sanding base.
5.
Set the clamp lever back in a locked position so
the end of abrasive paper is clamped securely.
6.
Release the clamp on the other end, and have the
other end of abrasive paper ready to be clamped.
7.
Maintain a proper tension on abrasive paper, and then
set the clamp lever on the other end in a locked position.
►
Fig.10:
1.
Abrasive paper
2.
Clamp
3.
Sanding base
4.
Clamp lever
5.
Stopper
8.
To remove the abrasive paper, release the clamps
on both ends and take the paper off the pad.
Using triangular/rectangular abrasive
paper
Optional accessory
CAUTION:
Make sure to install a hook-and-
loop pad correctly and securely.
A loose attach-
ment will run out of balance and cause an excessive
vibration resulting in loss of control.
CAUTION:
Be sure that a hook-and-loop pad
and abrasive paper are aligned and securely
attached.
CAUTION:
Only use hook-and-loop abrasive
papers. Never use pressure-sensitive abrasive
papers.
NOTICE:
The cap or the O-ring may come out of
the sanding base while replacing the pad. Be sure
to set the cap or the O-ring back in the circular
hole or the circular groove around the center of
the base before installing the optional pad.
►
Fig.11:
1.
O-ring
2.
Sanding base
3.
Circular groove
1.
Loosen and remove the four screws securing the
pad to the sanding base.
►
Fig.12:
1.
Screws
2.
Pad
3.
Sanding base
2.
Replace the standard-equipped pad with a trian-
gular/rectangular pad.
3.
Re-tighten the screws firmly to secure the triangu
-
lar/rectangular pad.
Triangular pad
►
Fig.13:
1.
Screws
2.
Triangular pad
3.
Sanding base
You can install the abrasive paper on the side of the pad
as illustrated.
►
Fig.14:
1.
Abrasive paper
2.
Pad
Rectangular pad
►
Fig.15:
1.
Screws
2.
Rectangular pad
3.
Sanding base
4.
Remove all dirt and foreign matter from the trian
-
gular/rectangular pad.
5.
Attach a sheet of optional hook-and-loop abrasive
paper to the triangular/rectangular pad, aligning the
dust-suction holes in the paper with those in the pad.
Triangular pad
►
Fig.16:
1.
Abrasive paper
2.
Triangular pad
3.
Dust-
suction holes
Rectangular pad
►
Fig.17:
1.
Abrasive paper
2.
Rectangular pad
3.
Dust-suction holes
6.
To remove the abrasive paper, peel it off from the
edge.