Makita BO4566J Instruction Manual Download Page 5

Page: 5 / 32

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing abrasive paper

NOTE:

Use Makita hook-and-loop sandpaper with this sander.

To attach the sandpaper: (Fig. 2 & 3)

1. Set the tool upside down so that the pad is on top.
2. Position the sandpaper to fit the shape of the base. Be

sure to align the holes on the sandpaper with the
holes on the pad (the dust will be sucked into these
holes; it is therefore important to leave them open).

3. Press the paper firmly over the pad.

To remove the sandpaper:

1. Set the tool upside down so that the sandpaper is on

top.

2. Grasping one corner of the sandpaper, peel it from the

pad.

NOTE:

• If the sandpaper is in good condition, save it for further

use.

When sanding in narrow, hard-to-reach areas (e.g.,
shutters, blinds, louvers), attach the cone-shaped
abrasive papers to the end of the pad (bottom and top).
To sand the end of thin materials, fold the abrasive paper
and attach to the side of the pad as shown in the figures.

Dust bag (accessory) (Fig. 4)

The use of the dust bag makes sanding operations clean
and dust collection easy. To attach the dust bag, fit the
bag’s entry port onto the dust spout on the tool. Make sure
that the hole in the bag’s entry port is just over the pimple-
like protrusion on the dust spout. For the best results,
empty the dust bag when it becomes approximately half
full, tapping it lightly to remove as much dust as possible.

Installing paper dust bag (accessory)
(Fig. 5)

Place the paper dust bag on the paper dust bag holder
with its front side upward. Insert the front fixing cardboard
of the paper dust bag into the groove of the paper dust
bag holder. Then press the upper part of the front fixing
cardboard in arrow direction to hook it onto the claws.

(Fig. 6)

Insert the notch of the paper dust bag into the guide of the
paper dust bag holder. Then install the paper dust bag
holder set on the tool.

(Fig. 7 & 8)

OPERATION

Sanding operation (Fig. 9)

CAUTION:

• Never run the tool without the abrasive paper. You may

seriously damage the pad.

• Never force the tool. Excessive pressure may decrease

the sanding efficiency, damage the abrasive paper and/
or shorten tool life.

Hold the tool firmly. Turn the tool on and wait until it attains
full speed. Then gently place the tool on the workpiece
surface. A finishing sander is generally used to remove
only a small amount of material at a time. Since the quality
of the surface is more important than the amount of stock
removed, do not bear down on the tool. Keep the base
flush with the workpiece at all times.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or
maintenance.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.

If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Abrasive paper (without pre-punched holes)
• Paper dust bag
• Paper dust bag holder
• Punch plate
• Dust bag

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ
from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according
to EN62841:

Sound pressure level (L

): 81 dB (A)

Sound power level (L

): 92 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.