background image

P  6/ 11

R

epair

[3] DISASSEMBLY/ASSEMBLY
[3] -2. Motor Complete, Gear Assembly (cont.)

ASSEMBLING

(1) Assemble Ball bearing 6803LLU to Gear housing. Refer to the drawing on the left in 

Fig. 7

.

(2) Mount Ball bearing 6806LLU to Spur gear 10. Refer to the drawing on the bottom in 

Fig. 6

.

(3) Assemble the Spur gear 10 section to Gear housing. Refer to the drawing on the upper right in 

Fig. 6

.

(4) Mount Oil seal 30 to Spacer. Refer to the drawing on the bottom in 

Fig. 5

.

(5) Assemble Plate 23, Spacer, Internal gear 48 and Spur gear 9C complete to Gear housing as drawn in 

Fig. 8

.

Fig. 9

Fig. 8

Plate 23

Oil seal 30

Internal gear 48

Gear housing

Spur gear 9C

complete

Spacer

Note:

 Assemble Spacer with the convex side

 

of it facing to Internal gear 48.

(6) Assemble the parts on the Flat washer 5 side to Gear housing as drawn in 

Fig. 9

.

1R027

Carrier A complete

Pins of Carrier 

A complete

Spur gear 19B

( 3 pcs.)

Flat washer 5

Carrier B

Pin 3  (9 pcs.)

Gear housing

< Note for Assembling of Pin 3 >

Do not lubricate on Pin 3. 

And, be careful that Pin 3 easily falls off.

Stop ring E-4

Spur gear 9C complete

1. Set Carrier A complete on 1R027, and

    assemble Carrier B and 9 pcs. of Pin 3.

3. Assemble Spur gear 19B to the Pins of Carrier A complete.

    And then, mount Flat washer 5 to Gear housing.

4. Assemble Stop ring E-4 to the shaft

    on Spur gear 9C complete.

2. While holding Internal gear 48

  with your fingers, assemble Gear housing

  to Carrier A complete section.

Summary of Contents for BCG140












Reviews:

Related manuals for BCG140