background image

ENGLISH (Original instructions) 

SPECIFICATIONS 

Model 9556HN 

9557HN 

9558HN 

Depressed center wheel diameter 

100 mm 

115 mm 

125 mm 

Spindle thread 

M10 

M14 

M14 

Rated speed (n) / No load speed (n

o

) 11000 

min

-1

 11000 

min

-1

 11000 

min

-1

 

Overall length 

271 mm 

271 mm 

271 mm 

Net weight 

1.9 kg 

2.0 kg 

2.1 kg 

Safety class 

/II 

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice. 
• Specifications may differ from country to country. 
• Weight according to EPTA-Procedure 01/2003 

 

END202-6 

Symbols 

The following show the symbols used for the equipment. 
Be sure that you understand their meaning before use. 

  Read instruction manual. 

 

 DOUBLE 

INSULATION 

 

 Wear 

safety 

glasses. 

 

  Only for EU countries 

Do not dispose of electric equipment 
together with household waste material! 
In observance of European Directive 
2002/96/EC on waste electric and 
electronic equipment and its 
implementation in accordance with 
national law, electric equipment that 
have reached the end of their life must 
be collected separately and returned to 
an environmentally compatible 
recycling facility. 

ENE048-1 

Intended use

 

The tool is intended for grinding, sanding and cutting of 
metal and stone materials without the use of water. 

ENF002-2 

Power supply

 

The tool should be connected only to a power supply of 
the same voltage as indicated on the nameplate, and 
can only be operated on single-phase AC supply. They 
are double-insulated and can, therefore, also be used 
from sockets without earth wire. 

 
 
 
 
 
 
 

For Model 9557HN 

ENG102-3 

Noise

 

The typical A-weighted noise level determined according 
to EN60745: 

Sound pressure level (L

pA

) : 86 dB(A) 

Sound power level (L

WA

) : 97 dB(A) 

Uncertainty (K) : 3 dB(A) 

Wear ear protection 

ENG208-5 

Vibration 

The vibration total value (tri-axial vector sum) 
determined according to EN60745: 

Work mode : surface grinding 
Vibration emission (a

h,AG

) : 7.5 m/s

Uncertainty (K) : 1.5 m/s

The declared vibration emission value has been 
measured in accordance with the standard test method 
and may be used for comparing one tool with another. 
The declared vibration emission value may also be used 
in a preliminary assessment of exposure. 
The declared vibration emission value is used for main 
applications of the power tool. However if the power tool 
is used for other applications, the vibration emission 
value may be different. 

 

WARNING: 

   

• 

The vibration emission during actual use of the 
power tool can differ from the declared emission 
value depending on the ways in which the tool is 
used. 

• 

Be sure to identify safety measures to protect the 
operator that are based on an estimation of 
exposure in the actual conditions of use (taking 
account of all parts of the operating cycle such as 
the times when the tool is switched off and when it 
is running idle in addition to the trigger time). 

 
 

Summary of Contents for 9557HN













Reviews: