background image

NOTE: 

• 

The workpiece will be cut a slightly different size 
from the templet. Allow for the distance (X) 
between the bit and the outside of the templet 
guide. The distance (X) can be calculated by using 
the following equation: 
Distance (X) = (outside diameter of the templet 
guide - bit diameter) / 2 

 

Dust nozzle set (Accessory) 

 
 
 
 
 
 
 
 

1

2

 
 

009754 

 
Use the dust nozzle for dust extraction. Install the dust 
nozzle on the tool base using the thumb screw so that 
protrusion on the dust nozzle fit to the notch in the tool 
base. 
Then connect a vacuum cleaner to the dust nozzle. 

   

009755 

 

MAINTENANCE 

 

CAUTION: 

• 

Always be sure that the tool is switched off and 
unplugged before attempting to perform inspection 
or maintenance. 

• 

Never use gasoline, benzine, thinner, alcohol or 
the like. Discoloration, deformation or cracks may 
result. 

To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, 

always using Makita replacement parts. 

 

ACCESSORIES 

 

CAUTION: 

• 

These accessories or attachments are 
recommended for use with your Makita tool 
specified in this manual. The use of any other 
accessories or attachments might present a risk of 
injury to persons. Only use accessory or 
attachment for its stated purpose. 

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center. 

• 

Straight & groove forming bits 

• 

Edge forming bits 

• 

Laminate trimming bits 

• 

Straight guide 

• 

Templet guide 25 

• 

Templet guides 

• 

Templet guide adapter 

• 

Lock nut 

• 

Collet cone 3/8", 1/4" 

• 

Collet cone 6 mm, 8 mm 

• 

Wrench 13 

• 

Wrench 22 

• 

Dust nozzle set 

 

 

1. Dust nozzle 
2. Thumb screw 

Summary of Contents for 900W













Reviews: