5
ENGLISH
Explanation of general view
1
Socket
2
Anvil
3
O-ring
4
Pin
5
Switch trigger
6
Metal part
7
Handle
8
Reversing switch lever
9
A side
10
B side
11
Clockwise
12
Counterclockwise
13
Expand
14
Hook
15
Fastening time
16
Seconds
17
Proper fastening torque for
18
Fastening torque
19
Limit mark
20
Brush holder cap
21
Screwdriver
SPECIFICATIONS
Model
6953
Capacities
Standard bolt ...................................... 10 mm – 16 mm
High tensile bolt .................................... 8 mm – 12 mm
Square drive ...................................................... 12.7 mm
No load speed (min
–1
) ...................................... 0 – 3,000
Impacts per minute ........................................... 0 – 3,000
Max. fastening torque ........................................ 150 N•m
Overall length ..................................................... 233 mm
Net weight............................................................... 1.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for fastening bolts and nuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety Hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES FOR TOOL
ENB003-1
1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a “live” wire will also make exposed
metal parts of the tool “live” and shock the oper-
ator.
2.
Wear ear protectors.
3.
Check the socket carefully for wear, cracks or
damage before installation.
4.
Hold the tool firmly.
5.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6.
The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Selecting correct socket
Always use the correct size socket for bolts and nuts. An
incorrect size socket will result in inaccurate and incon-
sistent fastening torque and/or damage to the bolt or nut.
Installing or removing socket
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the socket.
1.
For socket without O-ring and pin (Fig. 1)
To install the socket, push it onto the anvil of the tool
until it locks into place.
To remove the socket, simply pull it off.
2.
For socket with O-ring and pin (Fig. 2)
Move the O-ring out of the groove in the socket and
remove the pin from the socket. Fit the socket onto
the anvil of the tool so that the hole in the socket is
aligned with the hole in the anvil. Insert the pin
through the hole in the socket and anvil. Then return
the O-ring to the original position in the socket
groove to retain the pin. To remove the socket, follow
the installation procedures in reverse.
Switch action (Fig. 3)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Holding the tool (Fig. 3)
Hold the tool only by the handle when performing an
operation.
Do not touch the metal part.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
Hook
The hook is convenient for temporarily hanging the tool.
This can be removed without using a tool. This can be
installed on either side of the tool.
