6
ENGLISH
Explanation of general view
1
To avoid kickback, do support
board or panel near the cut.
2
Don’t support board or panel
away from the cut.
3
A typical illustration of proper
hand support and workpiece
support.
4
Hex wrench
5
Shaft lock
6
Tighten
7
Loosen
8
Saw blade
9
Outer flange
10
Inner flange
11
Outer flange
12
Hex socket head bolt
13
Saw blade
14
Setting protuberances
15
Hex socket head bolt
(For adjusting riving knife)
16
Cutting depth
17
Thumb nut
18
Thumb nut
19
For 45° bevel cuts
20
For straight cuts
21
Base plate
22
Lock-off button
23
Switch trigger
24
Vacuum cleaner
25
Limit mark
26
Brush holder cap
27
Screwdriver
SPECIFICATIONS
Model
5604R
Blade diameter ................................................... 165 mm
Max. cutting depth
At 90° ................................................................. 54 mm
At 45° ................................................................. 35 mm
No load speed (min
-1
) ............................................ 5,000
Overall length ..................................................... 320 mm
Net weight ............................................................. 3.6 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for performing lengthways and cross-
ways straight cuts and miter cuts with angles to 45° in
wood while in firm contact with the workpiece.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1.
Wear hearing protection.
2.
Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use. Don’t
use if lower guard does not close briskly over
saw blade.
CAUTION: If saw is dropped, lower guard may be
bent, restricting full return.
3.
Do not use blades which are deformed or
cracked.
4.
Do not use blades of high speed steel.
5.
Do not stop the blades by lateral pressure on the
saw blade.
6.
Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
7.
DANGER:
Keep Hands Away From Cutting Area.
Keep hands away from blades. Don’t reach
underneath work while blade is rotating. Don’t
attempt to remove cut material when blade is
moving.
CAUTION: Blades coast after turn off.
8.
Support Large Panels. (Fig. 1 & 2)
Large panels must be supported as shown in
Fig. 1 to minimize the risk of blade pinching and
kickback.
When cutting operation requires the resting of
the saw on the workpiece, the saw shall be
rested on the larger portion and the smaller
piece cut off.
9.
Use Rip Fence.
Always use a fence or straight edge guide when
ripping.
10. Guard Against Kickback. (Fig. 1 & 3)
Kickback occurs when the saw stalls rapidly and
is driven back towards the operator. Release
switch immediately if blade binds or saw stalls.
Keep blades sharp. Support large panels as
shown in Fig. 1.
Use fence or straight edge guide when ripping.
Don’t force tool. Stay alert–exercise control.
Don’t remove saw from work during a cut while
the blade is moving.
NEVER place your hand or fingers behind the
saw. If kickback occurs, the saw could easily
jump backwards over your hand, possibly caus-
ing severe injury.
11. Lower Guard.
Raise lower guard with the retracting handle.
12. Adjustments.
Before cutting be sure depth and bevel adjust-
ments are tight.
13. Use Only Correct Blades In Mounting.
Don’t use blades with incorrect size holes. Never
use defective or incorrect blade washers or
bolts.
14. Avoid Cutting Nails.
Inspect for and remove all nails from lumber
before cutting.
