background image

~4in

~4in

10. 

(A)

 Stand up your frame and push it against a wall. Lean your particle board 

canvas from Part One inside of the frame legs. They should be pressed against the 

support legs on each side, with about a 4in gap between them.

(B)

 From the back end of the horizontal frame legs, measure and mark 17.25in (43.8cm) out on 

each. Angle the canvases, so that the inside of the angle is on the 17.25in line and the top of the 

canvas is flat against the bottom beam. Attach to the canvases to the horizontal frame legs with 

two 

long wood screws

 on each side.

(C)

 Attach the top of the canvases to the bottom beam using three evenly spaced 

short wood 

screws

 on each.

Attaching the canvas 

Drew’s Note: WARNING: This frame is 
designed to lean against a wall for 
safety. If it is not against a wall, it could 
tip over. For added safety, you can 
toenail one of the vertical frame legs 
into a stud or use an L-bracket (not-
included), similar to what you would 
for an oven safety bracket. Look for a 
stand-alone update coming soon.

1.5in short wood 

screw

2in long wood 

screw

17.25in

Side view

17.25in

17.25in

Left view

Right view

10

Summary of Contents for M2 CNC





















Reviews: