Majestic Rio Case 2 Page 6 Dimension & Installation Manual Download | Manualshive

Page: 6 / 15

background image

The Majestic Shower Company Limited

Two North Place, Edinburgh Way, Harlow, Essex CM20 2SL England

Tel44 (0) 8448 001 500

Fac44 (0) 1279 635 074 [email protected] www.majesticshowers.com

6

7

8

Disassemble the Glass to Wall Brackets being careful not to damage the face plates.
With the clear plastic gaskets inserted both sides of the glass and wall screw plates
facing inwards, align the brackets centrally to the slots in the glass panel, hold them in
place and mark the screw hole positions on the wall.

Put the brackets to one side and use the suction glass lifters to carefully remove
the glass panel. Unscrew and remove the vertical wall profile.

Drill 7mm holes in the wall for the brackets as marked and insert wall plugs.

Rio Installation Guide - Surface Profiles

«
...
4
5
6
7
8
...
»

Summary of Contents for Rio Case 2
















Reviews:

No comments

Related manuals for Rio Case 2

Brand: Ramsey Winch Pages: 12

Brand: WEG Pages: 2

NANOPONIC Series

Brand: Aquatop Pages: 4

Brand: Sunex HD Pages: 17

Brand: Perel Pages: 20

Brand: TAGG Pages: 2

Library L100 Reader

Brand: TAGSYS Pages: 45

Brand: Index Braille Pages: 28

Turboflotor 750

Brand: Aqua Medic Pages: 12

NAVIGATOR - OPERATING GUIDE ADDENDUM

Brand: SABINE Pages: 2

Brand: AVL Looms Pages: 176

Brand: Oase Pages: 167

Brand: Pond Defence Pages: 5

Brand: ReelCraft Pages: 6

Brand: Calix Pages: 6

Brand: Yongxin Pages: 7

Brand: Quest Engineering Pages: 13

Brand: Eaton Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands