Majestic MERC32 Owner'S Manual Download Page 18

Majestic •  MERC32IN, MERC32IL, MERC32VN, MERC32VL Owner’s Manual  •  2401-981 Rev. L  •  9/20

18

Frequently Asked Questions and Troubleshooting 

A.  Frequently Asked Questions

Contact your dealer

 for additional information regarding operation and troubleshooting.  Visit www.majesticproducts.com 

to locate a dealer.

ISSUE

SOLUTIONS

 Condensation on the glass

This is a result of gas combustion and temperature variations. As the fireplace warms, this 

condensation will disappear.

 Blue flames

This is a result of normal operation and the flames will begin to yellow as the fireplace is al

-

lowed to burn for 20 to 40 minutes.

 Odor from fireplace

When first operated, this fireplace may release an odor for the first several hours. This is caused 

by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may 

also be released from finishing materials and adhesives used around the fireplace.

 Film on the glass

This is a normal result of the curing process of the paint and logs. Glass should be cleaned 

within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing 

process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See 

your dealer.

 Metallic noise

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to 

the sound produced by a furnace or heating duct. This noise does not affect the operation or 

longevity of the fireplace.

Is it normal to see the pilot flame burn  

continually?

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is 

turned off. Some optional control systems available with IPI models may allow pilot flame to 

remain lit. In a standing pilot system the pilot will always stay on.

Power Outages

 Battery backup (IPI Models)

This appliance (IPI Models) can be operated on battery power in the event of a power out-

age.  To access the battery pack, the decorative front, mesh and glass assembly must be 

removed.  Refer to Section 3 for more details. 

Wall above appliance feels hot to   

 the touch.

No action necessary.  This appliance ships with a non-combustible material attached. Speci-

fications of the attached non-combustible material are listed in the Installer’s Manual for this 

appliance.

Summary of Contents for MERC32




























Reviews: