background image

10 

54D5032

0"–12"

Maximum

Depth

12" Minimum

71"Minimum

Minimum 4"

From Both

Side Walls

FIREPLACE

WALL

COMBUSTIBLE

MATERIAL

AREA

4"

3"

2.5"

45°

2.5"

2.5"

1"

1.5"

1.5"

STUD

Follow  these  instructions  carefully  to  ensure  safe  installation.  Failure  to  follow 

instructions exactly can create a fire hazard.
The appliance cannot be installed on a carpet, tile or other combustible material other 

than wood flooring. If installed on carpet or vinyl flooring, the appliance shall be installed 

on a metal, wood or noncombustible material panel extending full width and depth of 

the appliance.

W

ARNING

CLEARANCES

CLEARANCES TO COMBuSTIBLES 

MANTEL CLEARANCES 

NOTE: The combustible area above the facing must not protrude more than 

3

/

4

" from the facing. If it does, 

it is considered a mantel and must meet the mantel requirements listed in this manual. 

Figure 5 - Clearances 

Figure 5a - Mantel clearances.

NOTE

All mantel shelves, regardless of depth, should be a mini

-

mum of 12" from top opening of fireplace. Mantel shelf 

shall not exceed 12" maximum depth at 12" minimum 

height from opening.

Summary of Contents for 300DVBH





















































Reviews: