background image

3

DVB4136 Direct Vent Gas Fireplace

20012322

Installation & Operating Instructions

This gas appliance should be installed by a qualified installer, 
preferably NFI or WETT (Canada) certified, in accordance with 
local building codes and with current 

CSA-B149.1

 Installation 

codes for Gas Burning Appliances and Equipment.  If the unit is 
being installed in a mobile home, the installation should comply 
with the current 

CAN/CSA Z 240.4

 code. For U.S.A Installations 

follow local codes and/or the current 

National Fuel Gas Code. 

ANSI Z223.1/NFPA 54.
FOR SAFE INSTALLATION AND OPERATION PLEASE 
NOTE THE FOLLOWING:

1 .  This fireplace gives off high temperatures and should be 

located out of high traffic areas and away from furniture 
and draperies.

2.   Children and adults should be alerted to the hazards of the 

high surface temperatures of this fireplace and should stay 
away to avoid burns or ignition of clothing.

3.  

CAUTION: Due to high glass surface temperature chil-
dren should be carefully supervised when  in the same 
room as fireplace.

Proposition 65 Warning:

 Fuels used in gas, woodburning or 

oil fired appliances, and the products of combustion of such 
fuels, contain chemicals known to the State of California to 
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

Remove any plastic from trim parts before turning the 
fireplace ON.
It is normal for fireplaces fabricated of steel to give off 
some expansion and/or contraction noises during the 
start up or cool down cycle. Similar noises are found 
with your furnace heat exchanger or car engine.  It is 
not unusual for your CFM Corporation gas fireplace to 
give off some odor the first time it is burned. This is due 
to the manufacturing process.

Please ensure that your room is well ventilated

-open all windows.

It is recommended that you burn your fireplace for at 
least ten (10) hours the first time you use it. If the op-
tional fan kit has been installed, place the fan switch in 
the “OFF” position during this time.

WARNING: Check with your electronics manufac-
turer before installing a television or other electronic 
device above this fireplace.

11.  When fireplace is installed directly on carpeting, vinyl tile 

or any combustible material other than wood, this fireplace 
must be installed on a metal or wood panel extending the 
full width and depth of the fireplace.

12.  This fireplace requires adequate ventilation and combus-

tion air to operate properly.

13.  This fireplace must not be connected to a chimney flue 

serving a separate solid fuel burning fireplace.

14.  When the fireplace is not in use it is recommended that the 

gas valve be left in the OFF position.

This appliance may be installed in an aftermarket 
permanently located, manufactured home or mobile 
home, where not prohibited by local codes.
This appliance is only for use with the type of gas 
indi-cated on the rating plate. This appliance is not 
convertible for use with other gases, unless a certi-
fied kit is used.

DVB4136

Certified To

ANSI Z21.88b-2008 / CSA 2.33b-2008 

Vented Gas Fireplace Heater

�������

���������

�����

������������

������������

������

�������������

�����

���������������

���������������

4.   Under no circumstances should this fireplace be modified. 

Parts removed for servicing should be replaced prior to 
operating this fireplace again.

5.  Installation and any repairs to this fireplace must be 

performed by a qualified installer, service agency or gas 
supplier. A professional service person should be contacted 
to inspect this fireplace annually. Make it a practice to have 
all of your gas fireplaces checked annually. More frequent 
cleaning may be required due to excess lint and dust from 
carpeting, bedding material, etc.

6.  Control compartments, burners and air passages in this 

fireplace should be kept clean and free of dust and lint. 
Make sure the gas valve and pilot light are turned off before 
you attempt to clean this fireplace.

7.  The venting system (chimney) of this fireplace should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your fireplace clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stocking or decorations be hung 
in the area of it.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10.  The flow of combustion and ventilation air must not be 

obstructed in any way. 

Summary of Contents for DVB4136





















































Reviews: