Main Eco Compact System 15 Installation And Service Manual Download Page 22

Page: 22 / 68

4.6

Accessories and options

4.6.1

Optional accessories

The table shows the accessories available for this boiler range.

Tab.16 Optional accessories

Part number Accessory
7211473

EP2 programmer

7212443

Twin channel timer wired

720971601

Wired room thermostat

720648301

Multifit condensate & PRV combined pump

720644401

Multifit 1m condensate drain pipe 'trace heating' element

720664101

Multifit 2m Condensate drain pipe 'trace heating' element

720664201

Multifit 3m condensate drain pipe 'trace Heating' element

720664401

Multifit 5m condensate drain pipe 'trace heating' element

5121379

Multifit remote secondary PRV kit

7683087

Multifit wired

on wall

outdoor sensor (System version)

For flue accessories (elbows, extensions, clamps etc.) refer to the Flue

Accessories Fitting Guide supplied in the literature pack.
Any of the above MUST be fitted ONLY by a qualified competent person.

Further details can be found in the relevant sales literature and at

www.baxi.co.uk

4 Description of the product

20644801

Baxi two channel programmable 7 day wireless sensor

Summary of Contents for Eco Compact System 15





































































Search results

Summary of Contents for Eco Compact System 15

Reviews:

Related manuals for Eco Compact System 15

Brands by name

Popular brands

Main Eco Compact System 15, Installation And Service Manual

Search results

Summary of Contents for Eco Compact System 15

Reviews:

Related manuals for Eco Compact System 15

Brands by name

Popular brands