background image

5.0 Clearances

8

© Baxi Heating UK Ltd 2009

200mm Min

780mm

450mm

200mm Min

5mm Min

5mm Min

450mm Min

For Servicing

Purposes

In Operation

20mm/5mm Min

see *NOTE:

5.1

For your Safety

1. This appliance must have been installed in accordance
with the manufacturer’s instructions and the regulations
in force.

2. Any modification that may interfere with the normal
operation of the appliance without express written
permission from the manufacturer or his agent could
invalidate the appliance warranty. In GB this could also
infringe the Gas Safety (Installation and Use) Regulations.

3. Your boiler must not be operated without the casing
correctly fitted.

4. Do not interfere with any sealed components on this
boiler.

5. Take note of any warning labels on your boiler.

6. Your boiler should have the following minimum
clearances for Safety and Maintenance 
(Fig. 34):-

Top

- 200mm

Bottom

- 200mm

Left side

- 5mm

Right Side

- 5mm

Front

- 5mm (In Operation)
- 450mm (For Servicing)

*NOTE:

The boiler can be operated with a clearance

of 5mm at the right. This is also sufficient for routine
maintenance. However a clearance of 20mm is
required if it is necessary to remove the secondary
heat exchanger. This should be considered when
siting the appliance and in the event of any
subsequent alteration in the area of installation.

7. If your boiler is installed in a compartment, do not use
it for storage purposes. Do not obstruct any purpose
provided ventilation openings.

8. Flammable materials must not be stored in close
proximity to your boiler.

9. Avoid skin contact when your boiler is in operation, as
some surfaces may get hot e.g. pipework.

10. Ensure that the flue terminal, outside the house,
does not become damaged or obstructed, particularly
by foliage.

11. It is important that the condensate drain system is
not blocked, modified or damaged in any way as this
would affect the operation of your boiler. Your installer
should have insulated any exposed pipework.

GB

- Heating Industry definition meaning England, Scotland,

Wales, Northern Ireland, Isle of Man and the Channel Isles

Summary of Contents for Combi 30 HE













Reviews: