background image

 INSTRUCTION MANUAL FOR DISHWASHERS

 

Page 10 of 12

 

 

UK 

Chap 6

 

SELF DIAGNOSTICS

  

 
The machine is equipped with a self-diagnosis system that registers and warns of a number of 
malfunctions.

 

Fault 

Description and possible remedies 

 

 

No rinsing

. The rinsing cycle was not completed correctly. Make sure that the rinsing 

nozzles are clean. 

 

 

No drainage. 

The water was not drained or drained incorrectly. Check that the drain 

pipe is not bent or crushed and that the siphon and filters are not blocked. In machines 
fitted with an overflow pipe, remove this before starting the drainage cycle.

 

 

 

Rinsing temperature reset fault. 

The boiler temperature did not reset in the set time 

during the washing cycle. Switch the machine off and then on and run a new cycle. 

S

AF

E

 

 

Water filling in tank fault.

 Make sure the pipes are connected correctly, and that the 

water tap is open. Where foreseen, check the presence of the overflow. Switch the 
dishwasher off and then on and fill again. 

 

 

Tank thermometer fault. (Probe open) 

The machine does not read the tank 

temperature value. Switch the dishwasher off and then on. 

 

 

Tank thermometer fault. (Probe short circuited) 

The machine does not read the 

tank temperature value. Switch the dishwasher off and then on. 

 

 

Boiler thermometer fault. (Probe open) 

The machine does not read the boiler 

temperature value. Switch the dishwasher off and then on.

 

 

 

Boiler thermometer fault. (Probe short circuited) 

The machine does not read the 

boiler temperature value. Switch the dishwasher off and then on. 

 

 

Boiler loading time out

: boiler not filled. Impossible to carry out rinse cycle. Check 

that the water tap is open. Switch the dishwasher off and then on and run a new cycle.

 

 

 

Tank temperature reset fault

The tank temperature did not reset in the set time 

during the washing cycle. Switch the machine off and then on and run a new cycle. 

S

AF

E

 

 

Electro-mechanical safety device:

 the boiler or tub safety thermostats have cut in, or 

the tub safety pressure switch has been triggered. 

S

AF

E

 

 

Level safety switch

: Incorrect water level in the tank. 

WARNING! Switching the dishwasher off and then on again "resets" the signals, if after carrying 
out the instructions given the problem persists, contact an Authorised Service Centre.

 

 
 
 
 

Summary of Contents for D501














Reviews: