Maico BSB FSD-TD Series Installation, Operation And Maintenance Instructions Download

Page: 20 / 20

Model

FSD-TD

Fire and Smoke Damper

Case Type

Rectangular Spigot Connection

Circular Spigot Connection

Flat Oval Spigot Connection

Case Material

Galvanised Steel

430 Stainless Steel - Ferritic (430) type 1.4016

316 Stainless Steel - Austenitic (316) type 1.4401

Blade Material

Galvanised Steel

430 Stainless Steel - Ferritic (430) type 1.4016

316 Stainless Steel - Austenitic (316) type 1.4401

FSD-TD S C1 B1 HF PM230-TF

FSD-TD Series

Fire and Smoke Dampers – Ordering Codes

MADE IN BRITAIN

SOLD TO THE WORLD

ADE IN

B R

I TAI N

Actuator Options

PM24-TF

24 volt spring return actuator

with thermal fuse

PM230-TF

230 volt spring return actuator

with thermal fuse

Installation Method

AF-BATT

Batt Frame

Angle Frame

HEVAC Frame

Cleats

For full details of the complete BSB Product Range, please refer to our individual product brochures, sales office or website.

BSB Engineering Services Limited

Unit 56, Trinity Trade Centre, Mill Way, Sittingbourne, Kent ME10 2PD, UK • Tel: +44 (0)1795 422609

For purchase orders and order related enquiries, please email: [email protected]

For pricing, technical and general enquiries, please email: [email protected]

Website: www.bsb-dampers.co.uk • A member of the Maico group

BSB Engineering Services Ltd. reserves the right to modify or withdraw any specification without prior notice that may result from

continuous product development. The information contained within this brochure is correct at the time of going to press. (FSDTD-05-2021)

Other Air, Fire and Smoke Control Products in the BSB Range:

A60 Series

Marine Fire Dampers

FD Series

Fire Dampers

Control Systems

FD-C Series

Circular Fire Dampers

BD Series

Backdraught Dampers

HD Series

Heavy Duty Dampers

SS Series

SlimSeal Dampers

FSD-C Series

Circular Fire/Smoke Dampers

ETD Series

Elevated Temperature Dampers

VC Series

Volume Control Dampers

Summary of Contents for BSB FSD-TD Series





















Search results

Summary of Contents for BSB FSD-TD Series

Reviews:

Related manuals for BSB FSD-TD Series

Brands by name

Popular brands

Maico BSB FSD-TD Series, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for BSB FSD-TD Series

Reviews:

Related manuals for BSB FSD-TD Series

Brands by name

Popular brands