background image

6

 

 

BA082201-en 

 

 

1.3

 

Intended Use 

 

 

This axle jack is to be used exclusively for the safe lifting of motor vehicles. Ob-
serve the rated load capacity. 

 

The axle jack shall not be modified without the express written consent of the 
manufacturer. In case of non-compliance the declaration of conformity be-
comes void. 

 

1.4

 

Inappropriate Use 

 

 

 

 

WARNING 

 

Any use other than described is inappropriate, for example: 

 

Climbing on the lift supports 

 

Transporting persons on the lift supports 

 

Usage as mobile work platform or for other lifting operations 

 

 

1.5

 

Requirements on Operating and Service Personnel 

 

 

 

WARNING 

 

All persons employed in the operation, maintenance, installation, removal and dis-
posal of the device must 

 

be at least 18 years old, 

 

be mentally and physically suited for these activities, 

 

be demonstrably trained and instructed in writing, 

 

have read and understood the operating instructions, especially the instructions 
what to do in the event of defects or malfunctions, 

 

be on record as having been instructed in safety guidelines, 

 

have practical experience in working with vehicle lifts and the hazards inherent 
in such equipment. 

 

 

 

 

Summary of Contents for AL II 2.0
































Reviews: