1
1 - Introduction
1 - Introduction
1 - Introduction
1 - Introduction
1 - Introduction
ABBREVIATIONS
A
P
r
e
z
y
l
a
n
A
r
e
w
o
P
0
0
1
5
l
e
d
o
M
B
I
P
G
d
r
a
d
n
a
t
S
s
u
B
t
n
e
m
u
r
t
s
n
I
8
8
4
-
E
E
E
I
D
E
L
t
h
g
il
r
o
t
a
c
i
d
n
i
l
e
n
a
p
t
n
o
r
f
F
P
,
W
,
V
,
A
A
V
d
n
a
r
o
t
c
a
F
r
e
w
o
P
,
s
t
t
a
W
,
s
t
l
o
V
,
s
e
r
e
p
m
A
y
l
e
v
i
t
c
e
p
s
e
r
,
s
e
r
e
p
m
A
t
l
o
V
d
n
a
U
P
M
t
i
n
u
r
o
s
s
e
c
o
r
p
o
r
c
i
m
B
S
L
,
D
S
L
t
i
b
r
o
t
i
g
i
d
t
n
a
c
i
f
i
n
g
i
s
t
s
a
e
l
R
R
M
C
o
i
t
a
r
n
o
i
t
c
e
j
e
r
e
d
o
m
n
o
m
m
o
c
UNPACKING
The Model 5100 is packed in reusable, shock resistant
packing material that will protect the instrument during
normal handling. In the event of shipping damage,
immediately notify the carrier and MAGTROL
Customer Service Dept.
Save all shipping materials for reuse when returning
the instrument for calibration or servicing.
POWER
The 5100 PA is factory wired for either 120 or 240
Vrms, 50/60 Hz, power at 40 volt amps, max. The line
cord is a detachable NEMA standard 3 wire which plugs
into the rear access power entry and filter module of the
5100 PA. The line cord must be detached from the PA
during servicing.
NOTE:
The standard 5100 is factory
wired for 120 Vrms power.
Wiring for 240 Vrms is available
on special order.
FUSE REPLACEMENT
Remove the line cord and carefully pry up and remove
the fuse holder. Use a 1/2 Amp slow blow fuse for 120
Vrms or a 1/4 Amp slow blow fuse for 240 Vrms power.
SAFETY
SECURELY GROUND the 5100 PA case by
connecting a good earth ground at the ground stud that
is located on the rear panel. Use a number 12 AWG, or
larger wire.
CONNECTORS
Plugs that mate with 5100 PA connectors:
Superior Electric Supercon
®
INPUT (plug, white, female) - PS50GWT
OUTPUT (plug, white, male) - PP50GWT
VOLTS HIGH (plug, black, female) - PS25GB
VOLTS LOW (plug, white, female) - PS25GWT
For your convenience, the above connectors are supplied
with your 5100 PA.
Use only the above connectors.
NOTE:
GPIB (IEEE-488) - 24 Pin bus
standard. Not included, must be
ordered separately.
MAXIMUM RATINGS
LOAD voltage: line to line, or line to common is 600
Vrms.
LOAD current: 50 Amperes rms, continuous.
100 Amperes rms, 30 sec. max.
REMOTE VOLTAGE SENSE: Line to line is 600
Vrms. Also, do not exceed 600 Vrms differential
between the VOLTS INPUT and AMPS OUTPUT
terminals.