manualshive.com logo in svg

Magtrol 3411, User Manual, Page: 55 / 59

Share
Download
Magtrol 3411 User Manual Download Page 55

46

Magtrol Model 3411 Torque Display

Appendix C: Computer Controlled Operation

APPENDICES

 

NOTE: 

You must power cycle the 3411 to restart the DHCP IP address 
negotiation.

 

NOTE: 

Ethernet communication will be lost during key entry into front 
panel menus after 2 minutes.

C.2 

ABOUT THE USB INTERFACE

To use the USB interface of the 3411, you must first install the drivers on your personal computer. 
Once the drivers are installed the 3411 will appear in the Windows device manager as a Virtual 
COM port.

C.2.1 

UsB d

RiveR

 s

etUp

 

FoR

 w

indows

Xp/w

indows

7 32Bit

Copy the 3411 USB driver files from the Torque 7 CD onto the local drive of your PC. The files are 
located in the 

\3411 DRIVER FOR WINDOWS\ 

folder on the CD. 

1. Run 

CP210xVCPInstaller_x86.exe

.

2.  Power on the 3411. The Found New Hardware Wizard window will pop up as shown below. 

On the Driver Installation window choose “Install from a list or specific location (Advanced)” 
option as shown in figure C–1 Driver Installation window.

Figure C–5  Driver Installation Window

3.  Click the Next button. The following screen will display. Browse the location you selected 

when executing 

CP210xVCPInstaller_x86.exe

.

Summary of Contents for 3411




























































Reviews:

No comments