background image

1 - Table of Contents 

ExpressCard 2000| Instant Issuance Card Personalization System | XY Transport Ribbon Cable Replacement Procedure 

 
Page 4 

Table of Contents 

Table of Contents ............................................................................................................................... 4

 

1

 

Required Tools, Materials, and Documents ........................................................................... 5

 

1.1

 

Required Tools ..................................................................................................................... 5

 

1.2

 

Suggested Tools .................................................................................................................. 5

 

1.3

 

Required Materials ............................................................................................................. 5

 

1.4

 

Suggested Materials ........................................................................................................... 5

 

1.5

 

Required Software and Documents ................................................................................. 5

 

2

 

Introduction ................................................................................................................................. 6

 

3

 

XY Transport Ribbon Cable Replacement Procedure ........................................................... 7

 

3.1

 

Prepare the Device ............................................................................................................. 7

 

3.2

 

Remove / Re-install the XY Transport Ribbon Cable .................................................... 8

 

 

Summary of Contents for ExpressCard 2000














Reviews: