Magnum MTP200 Operating & Parts Manual Download Page 4

4

SAFETY NOTES

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible injury or death.

This manual contains DANGERS, WARNINGS, CAUTIONS, NOTICES and NOTES which must be 
followed to prevent the possibility of improper service, damage to the equipment, personal injury or death. 
The following formatting options will apply when calling the readers attention to the DANGERS, WARN-
INGS, CAUTIONS, NOTICES and NOTES.

DANGER

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN 

DEATH OR SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious 

injury.

CAUTION

Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE 

Indicates a hazardous situation which, if not avoided, may result in property or equipment 

damage.

Note: Notes contain additional information important to a procedure and will be found within the regular text body 
of this manual.

OPERATING SAFETY

Before using the pump be sure to read and understand all of the instructions! This equipment was 
designed for specific applications; DO NOT modify or use this equipment for any application other than 
which it was designed for. Equipment operated improperly or by untrained personnel can be dangerous!   
Read the operating instructions and familiarize yourself with the location and proper use of all instruments 
and controls. Inexperienced operators should receive instruction from someone familiar with the equipment 
before being allowed to operate or set up the pump. The following points should be practiced at all times:

The area immediately surrounding the pump should be dry, clean, and free of debris.

NEVER

 start a unit in need of repair.

NEVER

 operate on a combustable surface.

NEVER

 operate the pump if any of the following conditions exist during operation:

1.

Noticeable change in engine speed.

2.

Sparking occurs.

3.

Engine misfires or there is excessive engine vibration.

4.

Protective covers are loose or missing.

WARNING

Never pump volatile or corrosive chemicals or solutions with this pump. These fluids 

could create serious safety, health and environmental hazards. High pressure 

increases the chance of pump explosion which may result in serious personal injury.

Summary of Contents for MTP200





















Reviews: