background image

MM-R/MM-RC Remotes Instruction Sheet

Part Number: 64-0012 Rev F

 

1

Sensata Technologies

www.SensataPower.com

Introduction

The MM-R remote allows you to turn the inverter on and off (ON/OFF), and 

provides three LED indicators for: inverter status (INVERT), status of any 

external AC power (AC IN), and to alert you of any faults (FAULT).
The MM-RC remote includes the remote ON/OFF switch and the same three 

LED indicators that the MM-R has, as well as three additional LED indicators 

for charger status (BULK, ABSORB, FLOAT).

MM-R

MM-RC

BULK

ABSORB

FAULT

FLOAT

AC IN

INVERT

ON/OFF

INVERT

AC IN

FAULT

ON/OFF

Figure 1, MM-R and MM-RC Remotes

Installation

Before proceeding, read the entire Installation section to determine how best 

to install your remote. The more thorough you plan in the beginning, the 

better your inverter needs will be met.

Installation Guidelines

•  Before connecting any wires determine the remote’s cable route 

throughout the home or vehicle/boat, both to and from the inverter.

• 

Always check for existing electrical, plumbing, or other areas of potential 

damage BEFORE drilling or cutting into walls to mount the remote.

• 

Make sure all wires have a smooth bend radius and do not become kinked.

• 

If installing this remote in a boat, RV, or truck ensure the conductors 

passing through walls, bulkheads, or other structural members are 

protected. This minimizes insulation damage (such as cha

fi

 ng) which can 

be caused by vibration or constant rubbing.

Unpacking and Inspection

Carefully remove the MM-R or MM-RC remote from its shipping container and 

inspect all contents. Verify the following items are included:

• 

MM-R or MM-RC remote display

• 

Bezel

• 

25’ Communication cable

• 

Two Phillips screws

• 

MM-R/MM-RC Instruction Sheet

If items appear to be missing or damaged, contact your authorized Magnum 

dealer or Sensata Technologies. Save your proof-of-purchase as a record of 

ownership; it is needed if the unit requires in-warranty service.

Summary of Contents for MM-R









Reviews: