background image

ii 

©2009 Magnum Energy Inc.

Disclaimer of Liability

Since the use of this manual and the conditions or methods of installation, 

operation, and maintenance of the ME-SBC

TM

 are beyond the control of Magnum 

Energy Inc., this company does not assume responsibility and expressly 

disclaims liability for loss, damage or expense, whether direct, indirect, 

consequential or incidental, arising out of or anyway connected with such 

installation, operation, use, or maintenance.
Due to continuous improvements and product updates, the images shown in 

this manual may not exactly match the unit purchased.

Restrictions on Use

The ME-SBC

TM

 shall not be used in connection with life support systems, life 

saving or other medical equipment or devices.  Use of the ME-SBC

TM

 with this 

particular equipment is at your own risk.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains important safety instructions that must be followed 

during the installation and operation of this product.  Read all instructions 

and safety information contained in this manual before installing or using 

this product.

WARNINGS:

•  All electrical work must be performed in accordance with local, state and 

federal electrical codes.
•  This product is designed for indoor / compartment installation.  It must not 

be exposed to rain, snow, moisture or liquids of any type.
•  Use insulated tools to reduce the chance of electrical shock or accidental 

short circuits.
•  Remove all jewelry such as rings, watches, bracelets, etc., when installing 

or performing maintenance on the ME-SBC

TM

 system.

•  Always disconnect the batteries or energy source prior to installing or per-

forming maintenance on the ME-SBC

TM

 system.  

Safety Symbols

To reduce the risk of electrical shock, 

fi

 re, or other safety hazard, the fol-

lowing safety symbols have been placed throughout this manual to indicate 

dangerous and important safety instructions.

WARNING:

 This symbol indicates that failure to take a speci

fi

 ed 

action could result in physical harm to the user.

CAUTION:

 This symbol indicates that failure to take a speci

fi

 ed ac-

tion could result in damage to the equipment.

Info:

 This symbol indicates information that emphasizes or supple-

ments important points of the main text.

Summary of Contents for ME-SBC





















Reviews: