background image

IMPORTANT

SERVICE POLICY

Owners of Magnetrol products may request the return of a control; or, any part of a control for complete rebuilding or 
replacement. They will be rebuilt or replaced promptly. Magnetrol International will repair or replace the control, at no cost to
the purchaser, (or owner) 

other than transportation cost 

if:

a. Returned within the warranty period; and,
b. The factory inspection finds the cause of the malfunction to be defective material or workmanship.

If the trouble is the result of conditions beyond our control; or, is 

NOT 

covered by the warranty, there will be charges for labour

and the parts required to rebuild or replace the equipment.
In some cases, it may be expedient to ship replacement parts; or, in extreme cases a complete new control, to replace the
original equipment before it is returned. If this is desired, notify the factory of both the model and serial numbers of the 
control to be replaced. In such cases, credit for the materials returned, will be determined on the basis of the applicability of
our warranty.
No claims for misapplication, labour, direct or consequential damage will be allowed.

RETURNED MATERIAL PROCEDURE

So that we may efficiently process any materials that are returned, it is essential that a “Return Material Authorisation” (RMA)
form will be obtained from the factory. It is mandatory that this form will be attached to each material returned. This form is
available through Magnetrol’s local representative or by contacting the factory. Please supply the following information:

1. Purchaser Name
2. Description of Material
3. Serial Number and Ref Number
4. Desired Action
5. Reason for Return
6. Process details

Any unit that was used in a process must be properly cleaned in accordance with the proper health and safety standards
applicable by the owner, before it is returned to the factory.
A material Safety Data Sheet (MSDS) must be attached at the outside of the transport crate or box.
All shipments returned to the factory must be by prepaid transportation. Magnetrol 

will not accept

collect shipments.

All replacements will be shipped FOB factory.

®

w

w

w

.m

a

g

n

e

tr

o

l.c

o

m

BENELUX Heikensstraat 

6, 9240 Zele, België

 

Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93  •  E-Mail: [email protected]

DEUTSCHLAND Alte 

Ziegelei 2-4, D-51491 Overath

 

Tel. 02204 / 9536-0  •  Fax. 02204 / 9536-53  •  E-Mail: [email protected]

FRANCE 40 

- 42, rue Gabriel Péri, 95130 Le Plessis Bouchard

 

Tél. 01.34.44.26.10  •  Fax. 01.34.44.26.06  •  E-Mail: [email protected]

ITALIA 

Via Arese 12, I-20159 Milano

 

Tel. (02) 607.22.98 (R.A.)  •  Fax. (02) 668.66.52  •  E-Mail: [email protected]

UNITED Unit 

1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL

KINGDOM 

Tel. (01444) 871313  •  Fax (01444) 871317  •  E-Mail: [email protected]

INDIA

C-20 Community Centre, Janakpuri, New Delhi - 110 0058

 

Tel. 91 (11) 41661840  •  Fax 91 (11) 41661843  •  E-Mail: [email protected]

BULLETIN N°:

BE 51-632.0

EFFECTIVE:

JULY 2007

SUPERSEDES:

New

UNDER RESERVE OF MODIFICATIONS

Summary of Contents for ECHOTEL 960













Reviews: