background image

 

Telemotive MLTX Transmitter Instruction Manual 

1/13/2012 

Page 9 of 19 

  BRIDGE            

 

          TROLLEY                  

 

             HOIST      

HOIST

 

 
 
 

 
 

     

AUX 1 

 

 
 

AUX 2

 

AUX 3

 

AUX 4

 

E STOP

 

ON

 

-

 

OFF

 

 
 
BATTERY 

AUX 5

 

AUX 4

 

2.1: MLTX TRANSMITTER STANDARD CONFIGURATION AND OPERATION  

  WARNING 

BEFORE OPERATING THE TRANSMITTER FAMILIARIZE YOURSELF WITH ALL SAFETY 
INFORMATION IN THIS MANUAL, THE CORRESPONDING RECEIVER SYSTEM MANUAL, 
APPROPRIATE MANUAL SUPPLEMENTS AND ANY OTHER LOCAL, STATE, OR FEDERAL 
RULES OR REGULATIONS ALREADY IN EXISTENCE. FAILURE TO FOLLOW THIS WARNING 
COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 1. 

Pre-engineered

 MLTX Control 

“MLTX-4L-3M-3S” has 4 Levers and 3 Speeds  

“MLTX-3L-3M-3S” has 3 Levers and 3 Speeds   

 

 

 

BRIDGE                         TROLLEY                            HOIST

AUX 1

AUX 2

AUX 3

AUX 4

E STOP

 

ON-OFF

 
BATTERY

 

       B

 

A          

 

BOTH

 

“MLTX-3L-3M-2S” has 3 Levers and 2 Speeds   
“MLTX-3L-5M-3S” has 3 Levers and 3 Speeds    
“MLTX-3L-3M-5S” has 3 Levers and 5 Speeds    

 

 

  BRIDGE            

 

         TROLLEY                  

 

           HOIST        

     AUX 

HOIST

 

AUX 1

 

AUX 2

 

AUX 3

 

AUX 4

 

E STOP

 

ON

 

-

 

OFF

 

 

BATTERY  

TANDEM

 

IND

 

 

AUX 1

AUX 2

AUX 3

AUX 4

E STOP

 

ON-OFF

BRIDGE       AUX TROLLEY     MAIN TROLLEY          HOIST         AUX HOIST

 
BATTERY 

TANDEM

 

IND.

 

TANDEM

 

IND.

 

“MLTX-5L-5M-3S” has 5 Levers and 3 Speeds    

Summary of Contents for Telemotive MLTX




















Reviews: