background image

 

Enrange Flex EM/EX Instruction Manual 

April 2019 

Page 9 of 19 

 

2.6  BATTERIES 

WARNING 

KNOW AND FOLLOW PROPER BATTERY HANDLING, CHARGING AND DISPOSAL PROCEDURES. 
IMPROPER BATTERY PROCEDURES CAN CAUSE BATTERIES TO EXPLODE OR DO OTHER SERIOUS 
DAMAGE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND 
DAMAGE TO EQUIPMENT. 

 

2.7  BATTERY HANDLING 

Use only batteries approved by Magnetek for the specific product. 
 
Do not dispose of a battery pack in fire; it may explode.  
 
Do not attempt to open the battery pack.  
 
Do not short circuit the battery. 
 
Keep the battery pack environment cool during charging operation and storage (i.e., not in direct sunlight 
or close to a heating source). 
 

2.8  BATTERY CHARGING 

For those transmitters equipped with battery chargers, please familiarize all users with the instructions of 
the charger before attempting to use.  
 
Do not attempt to charge non-rechargeable battery packs. 
 
Avoid charging partially discharged rechargeable batteries to help prolong battery cycle life. 
 
Avoid charging the battery pack for more than 24 hours at a time. 
 
Do not charge batteries in a hazardous environment.  
 
Do not short circuit the charger.  
 
Do not attempt to charge a damaged battery.  
 
Use only Magnetek Enrange approved chargers for the appropriate battery pack. 
 
Do not attempt to use a battery that is leaking, swollen or corroded. 
 
Charger units are not intended for outdoor use.  Use only indoors. 
 

2.9  BATTERY DISPOSAL 

Before disposing of batteries consult local and governmental regulatory requirements for proper disposal 
procedure. 

Summary of Contents for Flex EX Series




















Reviews: