background image

 

Enrange XLTX Intrinsically Safe 

Transmitter Instruction Manual 

April 2014 

Page 12 of 24 

3.1 

INSTALLING BATTERY PACK 

 
Prior to utilizing the XLTX transmitter, battery packs must be installed.    
 

3.1.1 

Approved Batteries for Intrinsically Safe Operation 

The XLTX transmitter has been tested and approved for intrinsically safe operation with the 
following AA (LR6) size batteries: 
 
 Duracell MN1500 
 Duracell PC1500 
 Energizer 

E91 

 

 Panasonic 

LR6XWA 

 Rayovac 815 
 
Use only the above battery manufacturers and part numbers as replacement batteries to maintain 
intrinsically safe operation. 
 

WARNING 

ONLY OPERATE THE TRANSMITTER IN HAZARDOUS ENVIRONMENTS WITH THE APPROVED 
BATTERIES. FAILURE TO USE THE APPROVED BATTERIES COULD RESULT IN SERIOUS INJURY 
OR DEATH AND DAMAGE TO EQUIPMENT.  ONLY USE 4 BATTERIES OF THE SAME 
MANUFACTURER AND MODEL NUMBER.

 

 

3.1.2 

Intrinsically Safe Alkaline Battery Pack 

 

The Intrinsically Safe XLTX comes standard with an intrinsically safe battery pack that holds four 
disposable AA alkaline batteries.   
 

 

Figure 2: Intrinsically Safe Battery Pack (Top and Bottom Views) 

 

To change the alkaline batteries in the battery pack, loosen the T10 star bit screws completely 
and remove the battery pack lid. Replace all the batteries with new ones.  
 

Summary of Contents for Enrange XLTX

























Reviews: