background image

1/9

LY71 with LX71-KR comparator function

Ver. 1 (2021.2)   

CS&S

LY71 & LZ71-KR 

Comparator function
Quick reference manual

1. First of all

2. Judgment display and judgment output

By combining LY71 with LZ71-KR (comparator unit), open 
collector output and relay output of up to 4 levels are possible 
when the comparator function is selected, and 1 level when the 
positioning function is selected. It supports both length display 
and angle display.

This manual mainly describes how to operate the comparator 
function. For detailed information on LZ71-KR, refer to the 
instruction manual.

LY71

LZ71-KR

Setting 
value 1

Setting 
value 2

Setting 
value 3

Setting 
value 4

Setting value and judgement

Judg.

Measuring value

Judgment

Judgment     status display (example)

(Condition: Setting value 3 

Measured value < Setting value 4)

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

Judgement output

Open collector output 

Relay output

Output circuit

Output 0

Output 1

Output 2

Output 3

Output 4

Display unit

+V

External output

Current value

Setting value

Setting value

Judgment display

(      to      ,             )

The corresponding 

lamp lights up

Lamp indicating the 

upper limit of the 

set value

Lamp indicating the 

lower limit of the 

set value

(Example of 4-level setting)

(Example of 
4-level setting)

Judges the lower and upper limits for the set value

(Output 0 to output 4)

The upper display shows the current value, and the middle and lower 

rows display the compare setting value.  Judgment against the set 

value is displayed by number and NG.

Judgment output timing chart

Judgment result is open collector output and relay output

Table of contents:

1. First of all
2. Judgment display and judgment output
3. Display of comparator setting value 

and judgment result

4. Installation / connection

4-1. Appearance
4-2. Insertion of expansion unit
4-3. I/O signal connection

5. Comparator function settings

(in advanced settings)

6. Comparator setting operation
7. Functional comparison between LZ71-KR

and old model LZ51-K/R

Setting 
value 1

Setting 
value 2 Setting 

value 3

Setting 
value 4

Large

Small

Size of compared value

4

Judg.

Judg.

Judg.

Judg.

1

2

3

5

4

Judg.

Judg.

Judg.

Judg.

Judg.

1

2

3

4

5

1

5

NG

Judg.

Judg.

Judg.

Judg.

Judg.

1

2

3

5

4

Summary of Contents for LY71










Reviews: