AC Switch Adjustment
Remove Turntable as outlined under "Turntable Re
moval". Rotate the On-Off Control Knob to the "ON"
position.
Loosen Switch Adjustment S c r e w (34) a n d remove
Switcl1 Cove1· (29) by removing Nut (31) and Washer
(30).
Slowly rotate switch body clockwise until the contact
strip (farthest from the actuator) is moved approxi
mately 1
/
64" from its rest. Tighten Switch Adjustn1ent
Screw (34) while holding the switch in this position.
Replace Switch Cover, Washer and Nut.
Automatic Trip
Failure of the mechanism to trip at the end of a 1·e
cord may be due to any one of the following:
S21S-1
1. Tightness or dirt on Pivots "J", see Figure 3.
R e m o v e C-clips from Pivots "J" and remove
Striker Feed Lever and S t r i k e r Arm. Clean
Levers and Pivots and replace. Re-fit C-clips
and check to be sure the Levers will travel their
full excursion when the sub-plate is tilted in a
45 degree angle.
2.
Striker Feed Lever (111) resting on sub-plate at
rear end.
3.
Insert a s1nall screwdriver between the sub-plate
and Striker Feed Lever
(111)
and exert a slight
upward pressure. The Striker Feed Lever should
be perfectly free on its pivot contacting the base
plate at its forward end only.
Dirt on Pins labeled "M", Figure 3.
Clean Pins "M" to be sure they are completely
free of any dirt and grease of any kind.
INSTRUCTIONS FOR SERVICING AND REPLACEMENT
OF PARTS
Tur11table Removal
1.
Place the On-Off control knob in the "OFF" posi
tion and remove t h e E-Clip (9) from center of
turntable.
2.
Remove turntable by grasping outside edge and
lifting straight upward with a slight back and forth
rotary motion.
3. Check that the Ball Thrust Cage (14) and Washers
are free fro1n foreign matter and lubricated with
a small quantity of light grease. The Ball Race
Cage is to be replaced with the open side facing
downward. There shouldbe a steel thrust washer
(15) immediately below a n d immediately above
the Ball Race Cage
(14).
(See Exploded View in
Figure
14). A
Resilient Washer
(12)
is f i t t e d
b e t w e e n the upper-most steel washer and the
turntable hub and self-aligning "dimpled" washer
is located below the bottom Thrust Washer.
4. Make certain that tl1e Idler Wheel (22) and Drive
'
Wheel
(17)
are in their retracted positions and will
clear the turntable rim when it is replaced.
5. Replace Turntable and secure E-Clip.
NOTE: Besides securing t h e turntable, the E
C lip also retains the Record Spindle to the Spigot
Housing. The Spigot Housing (93) and spindle are
notched so as to accept the center protrusion from
the E-Clip. Be sure the E-Clip seats properly
otherwise the Record Spindle Assembly will be
come loose.
Idler Wheel Removal and Replacement
1.
R e m o v e Idler Wheel Mounting Screw (24) and
Fiber Washer (23).
2.
Lift Idler Wheel (22) straight up fro1n its spindle.
3.
Replace Idler Wheel by reversing the procedure
just described, being certain that all fiber washers
under the Idler Wheel a r e replaced exactly as
they were found.
4. Check that the Idler Wheel rotates freely.
5.
Make sure that the Idler Wheel contacts the Motor
Pulley c o r r e c t 1 y and adjust as outlined under
"Idler Wheel Height Adjustment".
Motor Removal and Replacement
1. Remove Turntable as outlined under "Turntable
Removal".
2. Remove Switch Cover (29) by ren1oving Mounting
Nut (31) and Shakeproof Washer (30).
3. Remove ground lead and unsolder the black wire
fron1 the foremost switch contact.
4. Clip the red wire which connects to the AC socket
(this lead can be spliced when the motor is re
placed).
5. Re1nove the 3 motor mounting C-clips and washers.
6.
The motor can now be lifted f ro1n the mounting
studs complete with grommets (84) and mounting
plate.
7.
Reverse the foregoing procedure to reassemble.
If the switch contacts have bee11 ren1oved, be sure
t h e y are positioned correctly before replacing
switch cover. (See "AC Switch Adjustn1ent").
AC Switch Replacement
1.
R e m o v e
Nut
(31) a n d Washer ( 30)
and
lift
off
Cover (29).
2.
Lift out Contact Separator (25) and switch contacts
(26).
3.
Remove Adjustment Screw (34) and remove switch
housing mounting screw from under baseplate.
4. Reverse the foregoing procedure to reassemble.
