Magnavox W-08CR Owner'S Manual Download Page 3

To prevent injury to the user or other people and property damage, the following instructions 
must be followed. Incorrect operation may cause harm or damage. The seriousness is 
classified by the warning symbols below.

Safety Precautions

This symbol indicates the possibility of death or serious injury.

Definition of symbols used in this manual are as shown below.

!

!

WARNING

Always do this.

Never do this.

!

CAUTION

This symbol indicates the possibility of injury or damage to property.

Plug in power plug 

properly.

Do not modify power cord

length or share the outlet

with other appliances. 

Always ensure effective

grounding.

Unplug the unit if strange

sounds, smell, or smoke

comes from it.

Keep firearms away.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

   Otherwise, this may cause

   electric shock or fire due to

   excess heat generation.

  This may cause electric shock or 

  fire due to heat generation.

  Incorrect grounding may cause 

  electric shock.

  This may cause fire and electric

  shock.

  This may cause fire.

  This may cause explosion, fire and, burns.

  This may cause electric shock or

 fire  due to heat generation.

  This may cause electric shock.

  This may cause failure of machine

  or electric shock.

  This may cause fire and electric 

  shock.

  This may cause fire and electric 

  shock.

  This may cause electric shock or fire.

  If the power cord is damaged, it 

  must be replaced by the manufac-

  turer or an authorised service 

  centre or a similarly qualified per-

  son in order to avoid a hazard.

  This could be harmful to your health.

  Incorrect installation may cause 

  fire and electric shock.

  This may cause electric shock.

   This may cause an explosion or fire.

  This may cause failure and electric shock.

Do not operate or stop the

unit by inserting or pulling 

out the power plug.

Do not operate with wet

hands or in damp 

environment.

Do not allow water to run

into electric parts.

Do not use the socket if it is

loose or damaged.

Do not use the power cord

close to heating appliances.

Do not damage or use an 

unspecified power cord.

Do not point airflow at 

room occupants directly.

Always install circuit

breaker and a dedicated

power circuit.

Do not open the unit

during operation.

Do not use the power cord near 

flammable gas or combustibles, such

as gasoline, benzene, thinner, etc.

Do not disassemble or modify unit.

!

!

!

!

!

WARNING

!

2

!

!!

    

Summary of Contents for W-08CR




















Reviews: